A C8X11.5 single channel section is bolted to a gusset plate with M22 bolts. Assume A36 steel, 5.6mm thick web for the channel and an 8mm gusset plate. U = 0.80. The channel has a gross area of 2181mm2. The bolts have a shear stress of 457MPA. 30, 65 65 30 60 O O O 80 60 C8X11.5

A C8X11.5 single channel section is bolted to a gusset plate with M22 bolts. Assume A36 steel, 5.6mm thick web for the channel and an 8mm gusset plate. U = 0.80. The channel has a gross area of 2181mm2. The bolts have a shear stress of 457MPA. 30, 65 65 30 60 O O O 80 60 C8X11.5

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1.4) The design block shear strength is A) 234.900 kips B) 176.175 kips C) 211.050 kips D) 158.288…

A: The given figure is shown below:

Q: What is the shear stress in the 25-mm diameter bolt at pin C if P = 25 KN? A 50.93 MPa B 67.91 MPa…

A: Given, dc = 25 mm P = 25 kN

Q: A 2L 3 x 2 x ¼ LLBB tension double angle, A36 steel is subjected to a dead load of 12 kips and a…

A: For the given double angle member,

Q: REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P= 50…

Q: Problem 2. Using 22 mm diameter bolt, compute: a. t for Palone b. t for moment alone c. Critical…

A: Tension member connection and splice: It subjects the bolts to powers that will in general shear the…

Q: Calculate the maximum shearing stress developed in the 5 – 16mm diameter bolts 100 mm 100 mm P=…

Q: Problem 4 Determine the design tensile strength Pn of the MC18x58 channel shown based on yielding…

Q: 1. A double-channel shape, 2C8 18.75, is used as a tension member. The channels are bolted to a…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: 5. what is the shear rupture capacity of the shear plate of the shear connection in kips? (2 decimal…

A: a)Thickness of shear plate= 0.5 inA992: Fy = 50 ksi, Fu = 65 ksiA36: Fy = 36 ksi, Fu = 58…

Q: Determine the LRFD design tensile strength of the bolted connection shown. The angles are connected…

A: Given dia of bolt=16 mm fy =250 fx =405 diameter of hole=16+2 =18 mm

Q: How many (answer should be a whole number) 22-mm diameter rivets are required to fasten member BC to…

Q: A double-angle tension member, 2L 3 x 2 x 4 LLBB, of A36 steel is subjected to a dead load of 12…

A: 2L 3 x 2 x 1/4 LLBB section A36 steelDL = 12 kipLL = 36 kip db = 3/4 in

Q: Investigate both the tee and the bolts in the hanger connection in Figure . Include the effects of…

A: Solution a. Use LRFD. b. Use ASD.

Q: a. Determine the ultimate tensile strength of the tension member (channel) based on its gross area.…

A: For channel fu = 450MPa fy = 345MPa

Q: what is the bolt shear capacity of the flange connection in kips? (2 decimal places). Given: A992:…

A: W 1650 beam

Q: Problem # 8.0 The tension member shown is a C12 x 20.7 of A572 Grade 50 steel. Will it safely…

A: The channel section used = C12 × 20.7 The steel used = A572 grade 50 steel The magnitude of the…

Q: Home work Q1/ steel bar of rectangular secton 5cm by the 16 cm carries an axial load of 50 kn.…

A: As per guidelines please post Q 2 separately

Q: what is the flexural rupture capacity of the shear plate of the shear connection in kips?

A: A36: Fy = 36 ksi, Fu = 58 ksieffective bolt hole diameter = bolt hole diameter + 1/16"bolt diameter…

Q: Please show solutions on how to get the 0.5 and 1.0 value. The circle green in the figure. Civil…

A: The block shear failure consists of two failure surfaces The tension failure The shear failure The…

Q: The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with…

A: The given connection with dimensions as follows :

Q: Answer fast and send right answer

Q: Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by…

A: Shear Stress : Shear stress is the force which causes the deformation of a structure, component or a…

Q: limited to 48 ksi, determine the minimum bolt diameter that may be used for this connection. (coc00…

A: To find the minimum diameter of bolt (dmin.)-

Q: Determine the nominal axial compressive strength of the members shown in the following

A: The values and figure given in the question are as follows Length of column=L Effective length of…

Q: 1.2) The effective net area is A) 5.510 in B) 4.536 in C) 4.536 in D) 4.109 in

A: A double-channel shape, 2 C8*18.75, is used as a tension member. The channels are bolted to a…

Q: Determine the LRFD design strength and the ASD allowable strength. Neglect block shear. A36 steel…

Q: 6) Calculate the shear lag reduction factor, u, for the spliced W-shape tension member shown. Hint:…

Q: Since the reaction force at point A is 8975 #, The reaction force at point H is 7625#, the stress…

A: Given Data: The reaction force at point A is RA=8975 lbs. The reaction force at point H is RH=7625…

Q: Q2: Select a tension member is to consist of two C10 channels and two PL 1/2 x 11, arranged as shown…

A: Given : PD =200K PL = 320 Member length = 30ft U = 0.85

Q: the allowable tensile load on the members and weldlength and overlap length of

Q: For the beam shown find the value of Force (F) Ib and maximum stress due to flexure (Ob b ) psi if…

A: Given:- The shear force in the bolts = 300 lb The shear stress in beam = 120 psi The spacing between…

Q: A tension member with an allowable tensile stress of 0.6Fy is connected to the gus using four rivets…

A: According to given data A tension member with an allowable tensile stress of 0.6Fy is connected to…

Question

A C8X11.5 single channel section is bolted to a gusset plate with M22 bolts. Assume
A36 steel, 5.6mm thick web for the channel and an 8mm gusset plate. U = 0.80.
The channel has a gross area of 2181mm2. The bolts have a shear stress of 457MPa.
30, 65 65 30,
60
80
O O O
60
C8X11.5
(AISC Designation)
What is the allowable tensile strength due to rupture (kN)?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. what is the bolt shear capacity of the shear connection in kips? (2 decimal places)A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
please solve 1.1
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole Compute the nominal strength in bearing on Gusset plate only (since this will govern, it has smaller thickness than the main member PL ½ x 6)
I the Design the reinforcements of the given T beam below. bf=900mm bw=420mm tf=120mm d=550mm d'=80mm fc'=34MPA fy=415MPA USE NSCP 2015 mm2 A.Mu = 1400KN-m, As = mm2 B.Mu = 1700kN-m, As = mm2, As' = CS Scanned with CamScanner
16) what is the tensile yielding capacity of flange plate of the flange connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
Please show solutions on how to get the 0.250 value. The circle green in the figure. Civil engineering- steel design
1. The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The bolts are 3/4-inch in diameter. a. Draw the different potential failure lines. b. Compute the effective net area. 22" 2½" 2" 4 3" *₁ 3" ✓ 2" 2. A double-channel shape, 2C10 x 20 steel, Fy = 50 ksi and Fu = 70 ksi, is used for a built-up tension member as shown in the figure. The holes are for 12-inch-diameter bolts. PNA a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. YD Shape A 2" 2" -X Area, Depth, d | 3²²-|-1 3²² | 00 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ O O O Web Thickness, tw in. in. O 4" C10-30 x25 x20 5.87 10.0 10 0.379 % x15.3 4.48 10.0 10 0.240 4 4" Table 1-5 C-Shapes Dimensions Flange Width, b₁ 2 in. in. in.2 in. C15x50 14.7 15.0 15 0.716 1168 3.72 3% 0.650 % x40 11.8 15.0 15 0.520 x33.9 10.0 15.0 15 0.400 % 14 3.52 32 0.650 % %/16 3.40 3% 0.650 % C12-30 8.81 12.0 12 0.510 4 3.17 3% x25 7.34 12.0 12…
please solve 1.3
Compute the nominal strength based on yielding in KN. Determine the allowable tensile strength of Plate A in KN. Compute the allowable tensile strength at section a-1-2-2-4-c in KN.
5 please help meee
SOLVE FOR1 HR
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 2L5 x 3 x16 LLBB Determine the allowable tensile strength for ASD. Select one: а. 52.1 b. 104.2 c. 87.8 d. 43.9