snown. 7.12 A built-up steel member is composed of a W18 × 71 wide- flange section with a 12-in.-by--in. plate welded to its top flange, as shown. Locate the X-X centroidal axis. OP NIT= X- PROBLEM 7.12 12" Cover plate- 12" × ½" W18 x 71 Sym. -X MBJGORS

Q: Bottom chord of truss is composed of two angle bars each having a dimension of 192 mm x 95 mm x 5.4…

A: Bottom Chord of Truss : The horizontal member at lower edge of truss which carries the applicable…

Q: surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts…

A: To find greatest axial load P  Ebr=101GPa Est=193GPa

Q: The hook is subjected to three forces P, Q and S as shown. P=35kN and Q=45kN. 1. Determine the…

A: Given, P=35 KN Q=45 KN

Q: 1. Using the method of joints, determine the force in each member of the trusses shown. State…

A: To find force in all the members of the truss

Q: Determine the moment of the forces acting on the structure about point A. ´HIS IS AN EXAM. DO 90N…

A: In this question, Two forces of 90 KN and 20 KN are acting on the structure. 90 KN acts at 50 degree…

Q: 2 k 2 k 2 k - 5 ft- 5 f 5 ft 5 ft H F 5 ft as D 03. FUND-PROS 037 Pearen Calculate forces in memhers…

A: To find the force in member GF ,DG and CD-

Q: Problem 4 Determine the design tensile strength Pn of the MC18x58 channel shown based on yielding…

A:

Q: 2. Problem 7.8-2 Determine the adequacy of the hanger connection in Figure P7.8-2 Account for prying…

A: Question is based on hanger connection . Value of dead load , Live load and other dimensions are…

Q: 1. Identify zero force memeber. (Draw the FBD of Joint contain zero force member) B H|100 kN 60 kN K…

A: Identify the zero force member (Draw the FBD of joint contain zero force member).

Q: Determine the development length of the #9 bars. Is it safe?

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A 5¹8 x 15 DF axial combination 5 glulam is used as the tension member in a large roof truss. A…

A:

Q: 2. Problem 7.8-2 Determine the adequacy of the hanger connection in Figure P7.8-2 Account for prying…

A: Flange thickness bf = 4+4+38Flange thickness (bf) = 8.375 inWeb thickness    tw = 38+58…

Q: Statics

A:

Q: Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm…

A: Member BC: 300mm wide, 10mm plate attached to two 12mm plates at joint C, 3 A490 bolts, A36 plate

Q: USE METHOD OF SECTIONS, SHOW COMPLETE SOLUTION WITH FBD: ompute the force in member GM of the loaded…

A: To find force in member GM

Stair construction and layout

Stair is a type of vertical transportation in a building which consist of a series of steps in a flight of stairs that enable the vertical movement of people and materials from one floor to another. A staircase consists of steps that comprises of riser & tread, handrail, baluster, stair stringers, newel post and waist slab. The construction of staircase with all the components is termed as stair construction. A staircase is an enclosure that contains the entire stairway. The materials used for the construction of stairs are bricks, reinforced cement concrete, stone, lumber, steel and a combination of these materials.