Determine the maximum service load P (ASD) that the connection can resist. Use 27 mm Ø A490-N bolts, and 10 mm A-36 plate and a load P with a slope 1H: 2V. Assume that edge distance and bolt spacing are not critical. ***Note: Lod P is acting at a slope of 1H: 2V

Determine the maximum service load P (ASD) that the connection can resist. Use 27 mm Ø A490-N bolts, and 10 mm A-36 plate and a load P with a slope 1H: 2V. Assume that edge distance and bolt spacing are not critical. ***Note: Lod P is acting at a slope of 1H: 2V

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 60 b P P 150 100 100 100

Q: The bolted type connection will be used to assemble the given steel members. If PArmax = 8.36 t;…

Q: The angle shown below is A992 steel joined to a 3/4 in thick gusset plate (not shown) with 3 bolts.…

A: Consider the given data The bolts are group A bolts with thread not excluded from the shear plane,…

Q: 1.A tension member is 25 mm thick plate as shown. The bolts are 20 mm. diameter high-strength bolts.…

A: Plate 130 mm x 25 mmbolt diameter, db = 20 mmA36 grade of steel:fy = 250 MPafy = 400 MPaTo find:a)…

Q: PROBLEM 9.9 9.10 In the bolted connection of Figure 9.12, assume that the bolts are in. in diameter…

Q: 4. An UPE 300 is to be used as a tension member and it is bolted to a 10mm thick gusset plate with…

A: Tension member UPE 300 bolted connection. Fy = 275 N/mm2 Fu = 430 N/mm2 Ag= 5660 mm2 tw= 9.5 mm

Q: Check the bolted section of the given gusset plate connection assuming that the connection is done…

Q: o normal temperatures but wet in-service conditions. Assume =0.95 and the geometry factor is CA=1.…

A: 1 Area of the plate Ag Ag = 4×10 = 40 in2for A36 grade steel fy =36000…

Q: Determine the design tensile strength, Pn, of a 3/8 x 6 plate tension member shown in the figure.…

A: 38×6 plateFu = Ultimate strength = 58 ksiFy = Yield strength = 36 ksi

Q: Apply AISC LRFD procedure to design a welded connection for a vertical truss member L127x76x9.5 with…

Q: Fillet Welds Oriented Longitudinally and Transversely to the Load The two 4 x 4x3/8 angles shown in…

Q: A C9x20 is used as tension member connected to a gusset plate of ½ in thick (Figure 4). The member…

A: DL = 40kips LL = 80ips Thickness of the gusset plate = 12in. Steel used A36

Q: O Based on bolt capacity in shear. O Based on bolt bearing capacity. ® Based on block shear strength…

Q: A flanged bolt coupling consists of 6 - 12 mm - diameter bolts on a bolt circle of 320 mm i…

A: Given data in question Shearing stress Torque Diameter To find out Additional number of bolts…

Q: A bolted connection shown is bolted with a A-325 bolts with an allowable shearing stress of 207 MPa.…

Q: 35nun 15mm B Pu 200mm

A: According to given data Answer- 5 4-22 mm diameter bolts are used in a staggered bolted To,…

Q: A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of…

Q: The PL 18 x 1/2 as shown below are connected to PL 50 x 1/2 in with longitudinal SMAW fillet welds…

A: PL 18 X 1/2 connected to PL 50 X 1/2 Fillet weld 7/15 in fy = 50 ksifu = 65 ksiElectrode = E70

Q: he bolt is made of a material havin llowable shearing stress of 55.44 M

A: Given:- Allowable tensile stress=140.44MPa Allowable shearing stress=55.44MPa Axial load=17kN…

Q: Problem 7: The load that will be applied to the connection shown has a live load - to - dead load…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Determine the design strength of the connection shown in the Figure below. The bolts are 25 mm…

A: Given Data Diameter of bolt is given as 25 mm Ultimate tensile strength is given as 400 MPa Yield…

Q: Q1. Design the bolted connection. When a bracket is bolted to the flange of a column using a bracket…

A: Consider the free body diagram of given bracket connection with column flange as shown below.Bracket…

Q: The slip-critical bolted connection is shown below. The bolts are M24-8.8 and the tension member is…

Q: 5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt…

Q: A bolfed lap joint is shown below. The bolts used are A325, Grade 2, hof-driven vith diameter of…

A: Failure of bolted joints takes place in three ways- 1. Shearing failure of bolts. 2.Bearing failure…

Q: Design a welded connection for an MC9x23.9 of A572 Grade 50 steel connected to a 3/8-inch-thick…

A: A572 grade 50 steel connected to 3/8 inch thick gusset plateThe gusset plate is A36 steelTo…

Q: A channel C250x37 mm section is welded to a 9 mm gusset plate. Welding is not permitted on the back…

A: Slot Weld : Slot weld is used to attach flat plates using one or more holes in the top part. To fuse…

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Answer In order to calculate the minimum acceptable tensile service load we need to first find the…

Q: Use ASD to determine the width of the 5/8 inch thick A36 plate subjected to tension as shown below.…

A: ASD5/8 inch thick A36 platedead load, PD=85 kiplive load ,PL=80 kipTwo rows of 5/8 inch standard…

Q: Compute the service load capacity P for the welded bracket of the accompanying figure. The load is…

A: Given that :-A figure with welded bracket is given with following specifications.Live load = 70…

Q: Bolted Connections hear lap connection

A: Single Shear Lap Connection: 22 mm bolts Fnv = 300 MPa Bolts are in Single Shear Number of bolts = 6…

Q: Check the adequacy of the rigid beam to column welded connection shown. The beam is a 410 UB 53.7 of…

A: For grade 300 PLUS fy = 350 N/mm2 By ASD fa (allowed strength) = 350/1.67 = 209.6 N/mm2 ζa (allowed…

Q: The five-bolt connection must support an applied load of P = 3900 lb. If the average shear stress in…

A: Given data in question Load 3900 lbShear stress 35 ksi5 boltsTo find out Diameter of bolt

Q: For the connection shown, determine : a) Sigma (stress) on the plate, if N = -6 kN (negative sign…

A: Given:- Thickness of plate, t = 10 mm Width of plate, w = 2R = 2 x 30 = 60 mm Diameter of pin, d =…

Q: limited to 48 ksi, determine the minimum bolt diameter that may be used for this connection. (coc00…

A: To find the minimum diameter of bolt (dmin.)-

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: We know that LRFD capacity of the connection is given by minimum of the below three capacity1) Gross…

Q: The tension member shown is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter.…

A: Member =58×10 Steel A36 → Fy=36 ksi → Fu=58 ksi Bolts are 78 in. diameter.

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

P.
246 mm
76 mm 12 mm 25 mm
3
73 mm
74 mm
27 mm
56 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear stress in the bolts must be limited to 174 MPa, determine the minimum bolt diameter that may be used in the connection. Answer: d = i mm.
1 please with explanation
From the bolted connection shown, the diameter of bolts is 20 mm with the hole diameter equal to 3mm larger than the bolt diameter, the angular section is 100x75x8mm, with an area of 1340 mm^2. Thickness of gusset plate is 9 mm. the gusset plate. (a)If T = 200KN, compute the shearing stress on the bolts. (b)If the allowable shearing stress on the bolt is 145MPa, compute the value of T.
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
Problem 1: A butt joint shown in Figure ST – 127 using A325 bolts with a diameter of 16 mm with threads excluded in a shear plane. The plate used is A36 steel with Fy = 400 MPa. Use LRFD. Hole diameter is 3 mm larger than the bolt diameter. 1. Compute the design strength Pu of the connection based on bearing of the plate. Hint: The inner plate will govern. No need of checking the outer plate. 2. Compute the design strength Pu of the connection based on bolt shear. Hint: the bolt is in double shear. As is times 2 for every bolt. |32 84 84 12.5 mm T/2 T/2 22 mm 12.5 mm T/2- T/2 + T 180 mm Figure ST - 127
Load and resistance Factor design-tension members Q- Look into the block shear failure mode on the angle L4X4X linked to the 1-inch gusset plate with three 1-inch diameter bolts. Steel A36 is the substance.
For the bracket connection shown in the figure, determine the design strength in kips of the connection
dont give the picture of solution . give it in text
Five M20 8.8/ bolts are used in the connection between a beam and a column. Both sides of the cleat plate are welded to column using fillet weld (Manual metal arc AS4855 B-E43XX) with size of 5 mm. The design force transferred from beam to column is 300 kN. The cleat plate has thickness of 12 mm, fy = 300 MPa, and fü = 360 MPa. Determine the unit stress sustained by the weld