A square hollow section is connected to the flanges of ISMB 600 as shown in the above figure. The bracket is subjected to symmetrical vertical and horizontal load of each 50 kN. The size of SHS is 150 x 150 x 6 mm. Find the weld size required for the connection. 150 mm 100 mm ARM 50 KN A A 75 50 kN- 75 50 KN 150 11 VIEW-A-A

A square hollow section is connected to the flanges of ISMB 600 as shown in the above figure. The bracket is subjected to symmetrical vertical and horizontal load of each 50 kN. The size of SHS is 150 x 150 x 6 mm. Find the weld size required for the connection. 150 mm 100 mm ARM 50 KN A A 75 50 kN- 75 50 KN 150 11 VIEW-A-A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q20 The moment connection shown generates a maximum tensile or compressive load of 222.8 kips at each flange plate connection with the W14x145 column. Determine if stiffeners are needed by checking the applicable concentrated force strengths. The column is A992 steel and the connection occurs at the middle of the 20ft tall column. Use LRFD. PL /16 × 9 W14 × 145 W24 × 76 PL /16 X 9 a) Failure by flange local bending b) Failure by web local yielding c) Failure by web local crippling d) Column is OK without stiffeners
The welded frame beam connection consists of the framing angle 100 x 75 x12.5mm and the column W12 x 72. The welds are 9mm fillet welds made with E70 electrodes. All members are A36 steel. 12.5 mm a.) Determine Pu base on the capacity of the welds. Use LRFD design Factors. W 12x72 Angular Section 75 m 18.75 18.75 Angular section Angular section 800
1- The bolted type connection will be used to assemble the given steel members. Determine the safe load that a single turned bolt can carry. Consider only the effect of shear stresses. (St-37, H) t= 20 # ##* JL 90.90.9 40 50 315 9,96 t 9,04 t 9,40 t 9,70 t
Determine the maximum service load P (ASD) that the connection can resist. Use 27 mm Ø A490-N bolts, and 10 mm A-36 plate and a load P with a slope 1H: 2V. Assume that edge distance and bolt spacing are not critical. ***Note: Lod P is acting at a slope of 1H: 2V
Problem 5: The lap connection shown consists of a PL1/2"X3" plate connected to a ½ in gusset plate with ¼" longitudinal fillet welds as indicated. The plates are A36 steel and the electrodes are E70XX. Calculate the length L (in) of the connection to develop the full capacity of the plate. Hint: The full capacity of the plate will depend on the governing strength of the tension member. Neglect block shear. Use ASD 6" x 1/2" P [ T L 1/4 1/4 E70 - 13²x P 3" x 1/2"
Determine the maximum factored load P, that can be carried by the connection shown in the Figure P7. 1. The weld is 6 mm fillet weld. All structural steel is A36. E70 electrode is used
Given: The L8x4x½ shown below is welded to the gusset plate by its long leg. L₁ = 10" and L₂ = 7.5". L₁ L₂ Determine the gross area. 5.80 in² Calculate the length of the connection. 8.75 Calculate the eccentricity of the connection. 0.854" Calculate the width of the connected element. Calculate the value of the shear lag factor. Calculate the effective net area. in² II
Provide a balanced welded connection to mobilize the full capacity of the angle. ( Filler material :fy = 480 MPa, fu = 560 MPa, Members are S235) a Section a-a 10 mm 10 cm P { =37.14 mm 5 cm 16 mm Gusset Plate a
The truss below is pin connected at A and E, and is acted on by the forces shown. E A D B Identify all of the ZERO-FORCE MEMBERS by checking the boxes below (if there are none, leave all boxes unchecked): BF AF BC BH CD EG -GH AB CH DG DH DE -FH
2. Determine the adequacy of the clip angle connection shown. The allowable stresses are 100 MPa for shearing, 220 MPa for bearing, and 140 MPa for tension for the seat angle and the rivets. 45 kN 220 mm I 16 65 32 150 150x100x16 clip angle 20 mm o rivets 16 100
A rolled l-shaped beam is connected to a steel girder by 4-25mm bolts as shown. Determine the maximum end reaction that the beam can resist. (tw=15mm, Fy=248 MPa, Fu=400MPA) 60 mm 25-mm bolts- 3 @ 80 mm W 14 × 211 2 - 100 mm angle leg 60 mm
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm