Answered: • Compute the available block shear…

• Compute the available block shear strength of the connection based on the KN. (Diameter of hole is 20mm, ST37 steel is used, and thickness of plate is 7.5mm) 2@75 mm 3@75 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The five-bolt connection must support an applied load of P = 149 kips. If the average shear stress…

Q: 60 b P P 150 100 100 100

Q: 3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates of the same…

Q: q) what is the tensile rupture capacity of flange plate of the flange connection in kips? (2 decimal…

A: Yield Strength : Yield strength is a maximum stress a structure can bear beyond the maximum stress…

Q: o normal temperatures but wet in-service conditions. Assume =0.95 and the geometry factor is CA=1.…

A: 1 Area of the plate Ag Ag = 4×10 = 40 in2for A36 grade steel fy =36000…

Q: Determine the design tensile strength, Pn, of a 3/8 x 6 plate tension member shown in the figure.…

A: 38×6 plateFu = Ultimate strength = 58 ksiFy = Yield strength = 36 ksi

Q: what is the block shear rupture capacity of beam flange of the flange connection in kips? (2 decimal…

A: Tensile Strength: The Tensile strength of a material defines as the stress in tension that material…

Q: A connection using 3 bolts with the eccentricity is shown in Figure Q3. Determine: (a) Average shear…

Q: Determine the a) normal stress in rod (1), b) the shear stress in pin B and the shear stress in pin…

A: To find out the normal stress in rod 1 and shear stress in pin A and B.

Q: The connection of the drawbar and tie plate combination given below will be made by welding with two…

A: Welded connections: The point at which two or more pieces of metal are joined together is known as…

Q: REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P= 50…

Q: The following image shows a front and side view of the column connection. The bolts have a diameter…

Q: 5. Find the allowable strength of the welded connection with a minimum throat size shown below. Base…

A: The thickness of the plate = 10 mm The yield strength of the base metal (Fy) = 275 N/mm2 The…

Q: A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of…

Q: The following image shows a front and side view of the column connection. The bolts have a diameter…

Q: WT bracket is connected to a wide flange column with an E. 70 fillet welds as shown in the figure…

Q: 5. what is the shear rupture capacity of the shear plate of the shear connection in kips? (2 decimal…

A: a)Thickness of shear plate= 0.5 inA992: Fy = 50 ksi, Fu = 65 ksiA36: Fy = 36 ksi, Fu = 58…

Q: The connection is shown in Fig. 3. Two cover plates are applied to connect the steel plates by…

A: Given data:- The given size of fillet weld hf = 10 mm The tensile strength of steel plate f = 215…

Q: Problem 7: The load that will be applied to the connection shown has a live load - to - dead load…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: ) what is the weld capacity of the shear connection in kips? (2 decimal places) A992: Fy=50ksi,…

A: Beam W 16 x 50 (tw = 0.38 in, bf = 7.07 in, tf = 0.63 in)A992 (fy = 50 ksi, fu = 65 ksi)Effective…

Q: Determine the design strength of the connection shown in the Figure below. The bolts are 25 mm…

A: Given Data Diameter of bolt is given as 25 mm Ultimate tensile strength is given as 400 MPa Yield…

Q: Q1. Design the bolted connection. When a bracket is bolted to the flange of a column using a bracket…

A: Consider the free body diagram of given bracket connection with column flange as shown below.Bracket…

Q: A tension plate shown below is used to support suspended load "T". Gusset Plate- Fy = 248 MPa Fu =…

A: Given;

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Answer We know that LRFD capacity of the connection is given by minimum of the below three capacity…

Q: 10/10 find the tensile stress in upper plate in section 3-3 2 1 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN…

Q: The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in…

Q: what is the bolt shear capacity of the flange connection in kips? (2 decimal places). Given: A992:…

A: W 1650 beam

Q: Design a welded connection for an MC9x23.9 of A572 Grade 50 steel connected to a 3/8-inch-thick…

A: A572 grade 50 steel connected to 3/8 inch thick gusset plateThe gusset plate is A36 steelTo…

Q: what is the flexural rupture capacity of the shear plate of the shear connection in kips?

A: A36: Fy = 36 ksi, Fu = 58 ksieffective bolt hole diameter = bolt hole diameter + 1/16"bolt diameter…

Q: what is the tensile rupture capacity of flange plate of the flange connection in kips? (2 decimal…

A: Given that :-properties of beam are - Properties of material are -Required that :- tensile rupture…

Q: If the 18 mm plate is connected to two cover plate of 10 mm on top and bottom, what is the capacity…

Q: The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for…

A: Area = Force/ Shear stress

Q: limited to 48 ksi, determine the minimum bolt diameter that may be used for this connection. (coc00…

A: To find the minimum diameter of bolt (dmin.)-

Q: The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in…

A: The values and diagram given in the question are as follows: Applied load(P)=5300 kN or 5300*103 N…

Q: The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in…

Q: . The welded connection shown in the figure uses electrodes E70XX. The nominal weld strength of the…

Q: The angle 150x100x10mm is connected to a 8.5 mm gusset plate. The size of weld is 8 mm and using E70…

A: a) Find the length of the weld required at the toe of the angle.b) Find the length of the weld…

Q: The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear…

A: Given Load 371 kNStress 174 MPaNumber of bolts 5To find out Minimum diameter

Q: QUESTION 8 3. check the capacity of the shear connection. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi,…

A: Following formula will be used to calculate the yielding shear strength of the plate. Vn=A×Fy Where,…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

• Compute the available block shear strength of the connection based on the KN. (Diameter of hole is 20mm, ST37
steel is used, and thickness of plate is 7.5mm)
2@75 mm
3@75 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

STEP 1: BASIC DATA GIVEN :

VIEW

STEP 2: FORMULA TO DETERMINE THE BLOCK SHEAR STRENGTH :

VIEW

STEP 3: DETERMINATION OF BLOCK SHEAR STRENGTH :

VIEW

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. what is the bolt shear capacity of the shear connection in kips? (2 decimal places)A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
A tension plate shown below is used to support suspended load "T". Gusset Plate- F, = 248 MPa Fu = 400 MPa %3D 200 mm a) Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory).
The single shear connection consists of six 26-mm-diameter bolts. If the ultimage strength of the bolts is 720 MPa, determine the factor of safety for the connection at an applied load of P= 570 kN. P=570 kN
Determine the maximum service load P (ASD) that the connection can resist. Use 27 mm Ø A490-N bolts, and 10 mm A-36 plate and a load P with a slope 1H: 2V. Assume that edge distance and bolt spacing are not critical. ***Note: Lod P is acting at a slope of 1H: 2V
16) what is the tensile yielding capacity of flange plate of the flange connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
Two 75mmx8mm A36 steel plates are welded in a 10mm gusset plate. Assume a weld thickness of 7.5mm and that of electrode used is E70. Determine the following: 1. Total Length of weld if P=300KN 2. Load P based on block shear if L1=85mm and L2=92mm. Neglect end returns P -2-75mmx8mm plates 10mm-thk L1 gusset plate L2 end returns
Problem 5: The lap connection shown consists of a PL1/2"X3" plate connected to a ½ in gusset plate with ¼" longitudinal fillet welds as indicated. The plates are A36 steel and the electrodes are E70XX. Calculate the length L (in) of the connection to develop the full capacity of the plate. Hint: The full capacity of the plate will depend on the governing strength of the tension member. Neglect block shear. Use ASD 6" x 1/2" P [ T L 1/4 1/4 E70 - 13²x P 3" x 1/2"
Given: The L8x4x½ shown below is welded to the gusset plate by its long leg. L₁ = 10" and L₂ = 7.5". L₁ L₂ Determine the gross area. 5.80 in² Calculate the length of the connection. 8.75 Calculate the eccentricity of the connection. 0.854" Calculate the width of the connected element. Calculate the value of the shear lag factor. Calculate the effective net area. in² II
2. The figure shown is bolted with a diameter of 22mm. The inner plate material is 12mm x 315mm and the outer plate material is 9mm x 315mm. Assume hole diameter is 2mm larger than the bolt. T/2 T/2 F, = 345MPA, F, = 450MPA, F, = 207MPA, F, 1.2F, for bearing type connection. F, a friction type connection. = 117MPA for 45mm 75mm T/2 a. Determine the tensile capacity of the plates if it is a bearing type connection. b. Determine the tensile capacity of the plates if it is a friction type connection. c. Compute the minimum theoretical length of the lap if it is a bearing type connection. 75mm T/2 75mm 45mm A в А
The link shown is 9,25 in. Thick, and has a single Shear Pin connection. what is most nearly the required diameter (in) of the Pinif (tis average allowable shear Stress is 12ksi? 4 2in 20ksi
Assume that the gusset plate and welds are satisfied. A gap allowance of 1/16 inch is to be considered to fit the gusset plate in the HSS. The steel used in the tension member is ASTM A500 Grade C HSS 6 x 0.5 with a length of 30 feet. a.) Find the shear lag factor b.) Find the Effective net area (Ae) c.) Solve for the tensile strenngth 16-inch-long fillet weld HSS 6 x 0.5 1/2 in. thick gusset plate 17 inch long
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm