Two 75mmx8mm A36 steel plates are welded in a 10mm gusset plate. Assume aweld thickness of 7.5mm and that of electrode used is E70. Determine thefollowing:1. Total Length of weld if P=300KN2. Load P based on block shear if L1=85mm and L2=92mm. Neglect end returnsP-2-75mmx8mm plates10mm-thkL1gusset plateL2end returns

Strength of material: The area of material toughness, often known as materials mechanics, is…

Answered: wo 75mmx8mm A36 steel plates are welded…

wo 75mmx8mm A36 steel plates are welded in a 10mm gusset plate. Assume veld thickness of 7.5mm and that of electrode used is E70. Determine the ollowing:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 20 2okN KN Hinge B I the max nagative bonding momut at A

Q: O A fillet -welded joint of 6mm size is shown in the figure. the welded surfaces meet at 60-90…

Q: 8. For the plate tension member as shown in Figure 6.27 carrying axial service loads of 60 kips live…

A: Step 1: Factored Load Finding Factored load using the Load and Resistance Factor Design (LRFD)…

Q: A UNS G10350 steel shaft, heat-treated to a minimum yield strength of 75 kpsi, has a diameter of 1-…

A: Solution:-UNS G10350Minimum yield strengthσymin=75kpsiShaft rotates n=613rpmd=2316P=53hpSafety…

Q: The unsymmetrical I-section is cover plated with a 300mm W x 6mm thkplate. Use A 992 steel. 1)…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A belt i under van arcial thrust of 9.6 kN logether uwith va tranevowe force of 4.8 KN. 34 factor of…

Q: Compute the estimated actual endurance strength for a 75 mm -diameter rod made from SAE (AISI) 4130…

A: Solution: Given Data: AISI 4130 WQT 1000 steel=σn=81.2 Kpsi=559.85 MPadiameter=75 mmReliability=999%…

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown . If P =…

Q: For the frane shown below use unite. lbad melhed to determih verticaf defketion at c? E=200 kN = 300…

A: We are required to find the vertical deflection at C by using unit load method.

Q: H.WOA rod Consists of three bars of unequal dlameters as shown in fig., find the Stress in each bar…

A: Given: The modulus of elasticity is 200 GPa. Consider the figure,

Q: Exam A solid shaft of circular cross-section is subjected to torque 7 which produces a maximum shear…

Q: A prismatic bar is fixed at edges A and B as shown in figure. What is the axial force in CD portion?…

A: Given data- A prismatic bar fixed at edges A & B as shown- To Find- The value of the axial…

Q: Determine the maximum load, using factor of safety of five with respect to yield. a Material: Al…

A: Strength of material The area of solids strength, often known as materials mechanics, is concerned…

Q: Q2For the gable frame shown in fig. below, roof dead load = 60 KN/ m. Determine total static load…

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown, If P-7…

A: Given data in question Loading Cross section Elastic modulus Length To find out Total elongation

Q: Compound axial member ABC has a uniform diameter of d - 1.25 in. • Segment (1) is an aluminum [E, -…

A: Given data, E1 = 10000 ksi L1 = 70 in E2 = 17000 ksi L2 = 98 in €2 = 2100 micron in/in To find out…

Q: o T © فليصلي علی 69 Hw A shaft comSed nf Seymeats Ac, co and DB is fastened to vigid Surerts and…

A: Given data For bronze, Modulus of rigidity, G=35GPa For aluminium, Modulus of rigidity, G=28GPa For…

Q: A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place,…

Q: The equivalent stress for welding in given bracket connections would be if t = 5mm e i.e. Effective…

A: Effective throat thickness of weld te=5 mm,Fe410 steel & shop welding case,To Find-The value of…

Q: A fillet weld of size 6mm used to weld a plate of width 75mm to gusset plate to transfer a factored…

A: Size of weld = 6 mmPlate width = 75 mmFactored load = 120 kNSteel = Fe410To Find :The length of each…

Q: determine the stresses in the bolt and

A: Solution: Givendata, cross sectional area (alu) = 600 mm2 cross sectional area (steel) = 400 mm2 T =…

Q: n Fipure , with its dimensions, loadinp Status and material properties,different the rod is full…

Q: Fill in the blank/s with correct option: Amalgam is strongest in __________ strength after it has…

A: Amalgam is strongest in Compressive strength after it has set. The correct option is Option c.

Q: Solve and determine the design strength of a 1 - in length of a 14- in fillet weld formed by the…

A: Given, size of weld =1 inlength of weld = 14 inTensile strenght, FEXX= 70ksi

Q: True or FALSE ?? In the analysis of line welds, the variable Ju has dimensions of length cubed

A: For analysis of line welds loaded in torsion, the quantity Ju is used, which is the unit second…

Q: Solve for this please. Thank you!

A: As there are two questions posted, according to guidelines only the first is being answered. Kindly…

Q: 3.9 The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the…

Q: 3- If a load is applied on a wire and its length is stretched to the three times of its original…

A: Strain = Change in lengthOriginal length=3L - LL=2 Young's modulus = StressStrain=σ2 The young's…

Q: Determine stress

A: Given data Load =P=30 KN Area=A=20 mm 2 Determine stress =?

Q: 3- Determine: 4m a) The stresses in the bars shown after a temperature rise of 96°C. Brone har…

A: Compressive Stress: when a load (P) is acting on the bar having cross-sectional area (A)which…

Q: 20mm Steel Plates in the figure shown are connected by 9 rivets with 20mm diameter. If the Allowable…

A: Riveted connection: It is a type of steel connection. In this process, a metal pin is inserted into…

Q: unic 30 kN 50 KN 20KN 0=30° SOLVE FOR ACL SUPPORT 2m REACTIONS LN DICATE THE DIRECTION e e UNITS…

Q: and remperature increased to 360 Find reactionary forces at A and D_Considering RA = RA₁ and Rp = -…

A: Given: The modulus of elasticity of steel Es=200 GPa. The area of steel bar is As=1500 mm2. The…

Q: nectanqular and depth h=500mm is to carcry a seetion with width b=250 m %3D design bending mement M=…

A: Given :- Width of the rectangular section b = 250 mm Depth of the rectangular section h = 500 mm…

Q: 6.) A steel tape has the following properties: Nominal length: 50 m Standardised length: 50.010 m at…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub- parts for…

Q: A uniform bar is connected to a tapered rod 2. Both are subjected to axial loads as shown . If P =…

A: Given:- P = 7 KN

Q: Calculation question: Two side fillet welding int, N=660 kN (static loading, design value), sing…

Question

Two 75mmx8mm A36 steel plates are welded in a 10mm gusset plate. Assume a
weld thickness of 7.5mm and that of electrode used is E70. Determine the
following:
1. Total Length of weld if P=300KN
2. Load P based on block shear if L1=85mm and L2=92mm. Neglect end returns
P
-2-75mmx8mm plates
10mm-thk
L1
gusset plate
L2
end returns

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Given Data

VIEW

Step 3 (a) Total length of weld

VIEW

Step 4 (b) Calculation of load P based on block shear

VIEW

Step 5 Conclusion

VIEW

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given the compound bar below, determine the maximum allowable value of P if the change in length of the bar is limited to 5.67mm. The bar properties and allowable stresses are given in the table below. (answer in N)
The picture below Consist a brass ( EB = 100 Gla and AB and a Aluminum [ EA₁ = 73GPa | AA! each red exists a non- deformable rigid plate. The rods are stress free at 25°C. If the coefficient of thermal expansion for staat is taken 13.106 [m/m°c ] of a steel (E₂ -200CHPA and As = 1500mm ² = 2000 mind) JAT aluminiscent 2 = 1500 mm ² ) kod between at ds and temperature increased to up re increased to 350°C. A steel Find reactionary forces at A_ and _D_Considering RA = RA₁ and Rp = - Rp₁" ? Also find the deflection of plate B. 1.5 m a 18 = 19,10`6 [m/m="c] α = 24,10 € AL B Brass Im t D Aluminum 1.5m [m/m="c} Fant Fall f
Solve for joint @ A & C / AC
Find the stress in each rods. The 300 mm x 300 mm santrir m 2 m P-30 kN Steel L-0.5m E-200 GP A-500 m 1.5m Bronze L-2m E-70 GPa A-300 mm²
In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to a 16 mm gusset plate for a tensile load of 650 kN. Design the moment free welded connection. The distances of centroid of angle from the back side of legs are C₁=C₁ = 30.9 mm. The strength of the weld per mm thickness per mm length is 76 MPa.
The shaft system is made from aluminum and brass. -39 GPa) Aluminum (G=27 GPa) 1200 N The maximum shear stress tmax (MPa) in the shaft equals to: O675.45 Pc 1200 SL 90L PO
The assembly consists of two A992 steel bolts AB and EF and an 6061-T6 aluminum rod CD. When the temperature is 30°C, the gap between the rod and rigid member AE is 0.1 mm. Assume BF is also rigid. (Figure 1) Figure 400 mm A B 25 mm 50 mm D 0.1 mm 300 mm E 1 of 1 25 mm Part A Determine the normal stress developed in the bolts if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. of = Submit Part B σ₁ = Submit O HA Value Request Answer Provide Feedback ■μÅ Value Determine the normal stress developed in the rod if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units Request Answer wwwww Units ? wwwww Review ? Next >