O A fillet-welded joint of 6mm size is shown in thefigure. the welded surfaces meet at 60-90 degruand permissible stress in the fillet weld is 108 MPaThe safe load that can be transmitted by the joint isfसElcomm7 f

Answered: Image /qna-images/answer/0f4da0f5-6665-4c30-b162-cfbe010bd10f.jpg

O A fillet -welded joint of 6mm size is shown in the figure. the welded surfaces meet at 60-90 degree and permissible stress in the fillet weld is 108 MPa. The safe load that can be transmitted by the joint is. fस Klomma 55 7 f

O A fillet -welded joint of 6mm size is shown in the figure. the welded surfaces meet at 60-90 degree and permissible stress in the fillet weld is 108 MPa. The safe load that can be transmitted by the joint is. fस Klomma 55 7 f

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.11.4P

See similar textbooks

Similar questions

A lap welded joint of A36 steel plates must hold a tensile load. The lower plate is .5 inches thick and 7.7 inches wide. The upper plate is .5 inches thick and 4.8 inches wide. Use Class E60 series electrodes with 1/4 inch leg welds. Using side fillet welds only, A. find the maximum allowable tensile load the joint can support and determine the required overlap between the plates to achieve this strength B. what is the required overlap to meet the maximum tensile load
Situation 5. The angular section shown below is welded to a 12 mm gusset plate. Both materials are A36 steel with Fy = 250 MPa. The allowable tensile stress is 0.6Fy. The weld is E80 Electrode and 12 mm thickness. INNOVATIONS Properties of L 150x90x12: y = 50 shear stress of weld = 0.3Fu A = 2750 Allowable REVIEW INNOVATIE a K ➜ www A. 234 KN B. 349 KN b 13. What is the value of P without exceeding the allowable tensile the angle? C. 382 kN p. 413 kN 14. Find required length of the weld based on shear? A. 280 mm C. 300 mm D. 380 mm B. 320 mm 15. Find the required value of a? A. 108 mm B. 97.9 mm D. 185 mm NEW INNOVATIONS REVIEW INNOVATIOf REVIEW NEW INNOVATIONS
A channel C250x37 mm section is welded to a 9 mm gusset plate. Welding is not permitted on the back of the channel. All steel is A36 with Fy=250 MPa and Fu=400 MPa. Use E70electrodes having and Fu=485 MPa (SMAW) process. The maximum length of lap is 250mm. The size of fillet weld is 8mm. Assume the width of slot weld is 22 mm. Size of slot weld is 13mm Properties of C250x37 A = 4750 mm2 tw = 13.0 mm2 d = 254 mm a. Determine the force resisted by the slot weld in kN, when the full tensile capacity is 712.5 KN (from the gross yielding capacity using ASD) Hint: Full tensile Capacity = Force Resisted by Fillet and Slot Weld Round your answer to 3 decimal places.
The double T-beam is fabricated by welding the three plates together as shown. Part A Determine the shear stress in the weld necessary to support a shear force of V=78 kN�=78 kN.
ANGLE IS CONNECTED AT A GUSSET PLATE /3 FILLET WELDS USING E70 ELECTRODES AND A-50 STEEL, DETERMINE THE SHORTEST LENGTH L1 and L2 TO FULLY DEVELOP THE STRENGTH OF THE ANGLE USE SHEAR LAG FACTOR OF U= 0.75 LRFD. 8 61 L2 L1 L5 X5 X
a. Determine the design strength of a 1-in length of a 1/4-in fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength FEXX = 70 ksi. Assume that load is to be applied parallel to the weld length.b. Repeat part (a) if the weld is 20 in long.c. Repeat part (a) if the weld is 30 in long.
A tie member of a truss consisting of an angle section 65 x 65 x 6 of Fe 410 grade is welded to an 8mm gusset plate. Design a weld to transmit a load equal to the full strength of the member. Assume shop welding.
Tension Member Design Problem 1. A channel shape is under 50 kips dead and 100 kips live tensile axial load as shown in the figure. The member is connected to a gusset plate with 10 inch longitudinal welds. Find the lightest channel shape to carry the loading. Use only vielding and rupture limit states to design. Use 50 ksi steel (Fy=50 ksi, Fu=65 ksi). (a) Assume yielding limit state controls in the design process; (b) After selecting the lightest section, check the rupture limit state. Do not redesing if needed. 1 Pa=50 kips PL=100 kips 10"
Determine the maximum service load, P, that can be applied if the live load-to-dead load ratio is 2.0. Each component is a PL 3⁄4 x 7 of A242 steel. The weld is a 1⁄2-inch fillet weld, E70 electrode. a. Use LRFD. b. Use ASD.
An I-section bracket is connected to the column as shown. The size of weld is 6 mm on web and 10 mm on flange. What will be the safe load (in kN) that can be carried by the connection? Assume NA for whole weld = 110.57 x 106 mm4. Use Fe410 grade steel. 240 mm 170 mm P unu 00t * 280 mm unu 00t 280 mm
A welded bracket connection is shown in figure. It supports a factored load of 150 kN at a distance of 120 mm from the face of column. Design the fillet weld on two sides. Grade of steel = Fe410, f. = 250 MPa. y 120 mm P₁ = 150 kN Fillet weld t = 12 mm
Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).