A tie member of a truss consisting of an angle section 65 x 65 x 6 of Fe 410 grade is welded to an 8mm gusset plate. Design a weld to transmit a load equal to the full strength of the member. Assume shop welding.

A tie member of a truss consisting of an angle section 65 x 65 x 6 of Fe 410 grade is welded to an 8mm gusset plate. Design a weld to transmit a load equal to the full strength of the member. Assume shop welding.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Calculate the maximum shear force in the welds and the required weld size in the given figure. Where…

A: Given that :-A weld structure is given in the question with following specifications :P = 50 kNX =…

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

A: To Determine Largest allowable gauge pressure, P

Q: Two plates of Steel A72 Gr 50 are connected with each as shown in Figure 5. E70XX Electrodes were…

A: Given:- Steel A72Gr500 fillet weld=7/16 To find:- design strength by LRFD and ASD

Q: Situation 6: The lap splice shown will develop a full strength as shown in the figure. Us The width…

A: Data Given:Width of plate = 150mmThickness of plate = 12mmFy = 345To find out the size of weld by…

Q: O A fillet -welded joint of 6mm size is shown in the figure. the welded surfaces meet at 60-90…

Q: Determine the total LFRD design strength and the total ASD allowable strength of the 5/16 – in E70…

A: We will solve this question in step no. 2

Q: A UNS G10350 steel shaft, heat-treated to a minimum yield strength of 75 kpsi, has a diameter of 1-…

A: Solution:-UNS G10350Minimum yield strengthσymin=75kpsiShaft rotates n=613rpmd=2316P=53hpSafety…

Q: 6. Design the tension plate attached to the wide-flange (W) section as well the welds, assuming the…

A: Step 1:

Q: Q- A fillet weld of size 6mm used to weld a plate of width 75mm to gusset plate to transfer a…

A: A fillet weld-Size = 6 mm Plate width = 75 mm to gusset plateFactored load = 120kN, Site weld and…

Q: Fillet Welds Oriented Longitudinally and Transversely to the Load The two 4 x 4x3/8 angles shown in…

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Given- Properties of WT- 12×38Ag=11.2 in2y'=3.0 inbf=8.99 inA992 steel-fy=50 ksiFu=65 ksiLL=3DL

Q: The connection of the drawbar and tie plate combination given below will be made by welding with two…

A: Welded connections: The point at which two or more pieces of metal are joined together is known as…

Q: Solve a 100 x 100 x 10mm angle is to be welded to a gusset plate shown. The angle carries a load of…

A: Given strength of fillet weld 94 mpa Size of fillet weld = 8 mpa Load to be carried = 185 kn

Q: Two steel plates are lap jointed in a workshop using 6 mm thick fillet weld as shown in the figure…

A: Two steel plates are lap jointed in a workshop using 6 mm thick fillet weld The ultimate strength of…

Q: 7. Design the welds indicated to develop the full strength of the angles and minimize eccentricity.…

A: Problem Statement:Design the welds indicated to develop the full strength of the angles and minimize…

Q: A hanger is suspended from a plate that is welded to a wide flange beam as shown. The plate requires…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: 3 Specify the plate thickness and weld size to be used for the joints in the accompanying Figure…

Q: Two 3/16" E70 fillet welds of 15 in. Iong are subjected to a load P. Using LRFD, compute the…

A: Answer (a) Minimum weld length requirement Minimum weld length may not be less than 4 times the…

Q: Determine the design strength for C-shaped welds. USE E70 electrodes and 5/16" weld. 2011d

A: Given, E70 electrodes Weld thickness (w) = 5/16"

Q: Material Strengths: Fy= 248 MPa, Fu= 400 MPa Method: Use ASD. A single angle L203X152X19 is welded…

Q: Situation 1: The lap splice shown will develop a full strength as shown in the figure. Using E70 The…

A: d=39mm

Q: The connection is shown in Fig. 3. Two cover plates are applied to connect the steel plates by…

A: Given data:- The given size of fillet weld hf = 10 mm The tensile strength of steel plate f = 215…

Q: Determine the maximum effective net area of the fillet weld using the maximum weld allowed by the…

Q: can be decided as the Class b section. Determine the design value of axial load capacity.

Q: A lap welded joint of A36 steel plates must hold a tensile load. The lower plate is .5 inches thick…

A: Lower plate tensile load = 0.5 inch thickWidth of lower plate = 7.7 inch wideUpper plate tensile…

Q: Q1 Two 3/16" E70 fillet welds of 15 in. long are subjected to a load P. Using LRFD, compute the…

A: Answer We are given size of weld (w)= 3/16 in Length of weld L = 15 in E 70 electrode

Q: Q3: Design 5/16-in SMAW fillet welds for the plate shown in figure below if A36 steel and E70…

A: Given data : design a 5/16 -in SMAW fillet welds for the plate ( for the given figure) use A36…

Q: uation 4: The lap splice shown will develop a full strength as shown in the figure. Using E70 el e…

A: I have solved your problem

Q: An I-section bracket is connected to the column as shown. The size of weld is 6 mm on web and 10 mm…

Q: Q- IF THE LENGTH OF THE WELDED JOINTS FOR TWO PLATES IS 700 MM FOR A PLATE OF 8 MM AND 10 MM WELDED…

A: Given- Length of welded joints=700 mm,plates thickness 8 mm & 10 mm,weld size= 6 mm. It is…

Q: A channel C250x37 mm section is welded to a 9 mm gusset plate. Welding is not permitted on the back…

A: Slot Weld : Slot weld is used to attach flat plates using one or more holes in the top part. To fuse…

Q: The equivalent stress for welding in given bracket connections would be if t = 5mm e i.e. Effective…

A: Effective throat thickness of weld te=5 mm,Fe410 steel & shop welding case,To Find-The value of…

Q: A fillet weld of size 6mm used to weld a plate of width 75mm to gusset plate to transfer a factored…

A: Size of weld = 6 mmPlate width = 75 mmFactored load = 120 kNSteel = Fe410To Find :The length of each…

Q: The equivalent stress for welding in given bracket connections would be if t = 5mm e i.e. Effective…

A: Effective throat thickness of weld te=5 mm,Fe410 steel & shop welding case,To Find-The value of…

Q: Solve and determine the design strength of a 1 - in length of a 14- in fillet weld formed by the…

A: Given, size of weld =1 inlength of weld = 14 inTensile strenght, FEXX= 70ksi

Q: The torque (C) to be transmitted by a drive at the welds is 650 Nm. Knowing that the diameter of the…

Q: and L = ( 6.5 + 1.5b) inches. Determine the design strength oR, for the concentrically loaded weld…

A: Fillet weld: - It is defined as the process in which two metal pieces join together perpendicularly…

Q: what is the available strength of the connection?

Q: Design a double angle tension member that is fillet welded to a gusset plate. Assume that the angles…

A: 1).Design and select a trial tension member See Table 5-8 on page 5-49 of the AISC manual. - Select…

Q: Determine the required diameter of a plug weld using E60 electrodes on A-36 steel to develop the…

A: We have to determine the value of required diameter of a plug weld using E60 electrodes on A36 steel…

Q: 5. Select a pair of channels and design the fillet welds using SMAW process. The loading is 85% live…

A: Step 1:For A36 SteelGiven:Live Load (LL) = 170 kipsDead Load (DL) = 30 kipsDesign Load…

Q: Situation 4: The lap splice shown will develop a full strength as shown in the figure. Using E70…

A: 29 mm

Q: In an industrial shed an edge support consisting of 2L-110 x 110 mm is to be connected to a 16 mm…

Q: Determine the size of the weld using E60 electrode. Dead Load = 38 kip and LL = 95 kips (Service…

A: Nominal strength of weld is given by Rn = fnw*Anw fnw = Nominal weld strength fnw = 0.6*fEXX fnw =…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q#4: Design Fillet welded connection using E65X electrodes to connect three plate sections (W=20in & t=0.75") for transmitting dead load of 10k & live load of 140k.Consider minimum weld thickness (S=5/8") with "A36" member steel (fy=36 ksi & fu=58 ksi).
Two steel plates, each 400mm wide and 12mm thick, are to be joined together by a lap splice (single). The electrode to be used for the weld has a nominal tensile strength of 550Mpa. Determine the following:a. the maximum weld size that can be usedb. effective net area of the fillet weld using the maximum weld size allowed by the manualc. the maximum load that can be resisted by the weld using the maximum weld size allowed by the manual.
Regardless of the design load, the effective length of a 5/8 in. fillet weld that is subjected to stress in a longitudinal direction should not not be less than A. 2 in. B. 2 1/2 in. C. 3 in. D. 3 1/2 in.
* 2. Calculation question: Two side fillet welding joint, N=660 kN (static loading, design value), using angle steel with 2L 110×10. The thickness of gusset plate is t1=12 mm, using the steel of Q235B and electrode of E43, SMA welding. Determine the leg size hf and actual lengths of two welds. 300 N 2L110×10 t=12 110
If the structural frame is replaced to structural steel and the connections is to be designed, determine the following Determine the centroid of the weld measured from the given origin A. Determine the direct shear load in the welds. Determine the required size of the fillet weld(E60xx) if the maximum resultant load is 750,000 N/mm
10 mm fillet welds Determine the design capacity of the welded lap steel connection shown below. All steel plates are 50X10mm dimension. Both fillet welds are 10mm E48XX SP, continuous across the full plate width. If the connection was tested to failure, which component would fail first.
If the design tensile strength Phi Pn of a tension member is controlled by rupture failure. Which of the following actions will NOT increase its capacity? using welds instead of bolts using larger cross section of the member increasing strength of steel using thicker gusset plate
a welded connection is in eqilibrium under the action of the four forces shown. Knowing that FA=8lbs and FB= 16lbs, determine the magnitudes of other two forces *3dec places all final
See the image. Two steel plates are welded together. The thickness of the bottom plate is 10mm and the thickness of the top plate is 8mm. What is the maximum and minimum sizes of the weld.
Solve for joint @ A & C / AC
In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to a 16 mm gusset plate for a tensile load of 650 kN. Design the moment free welded connection. The distances of centroid of angle from the back side of legs are C₁=C₁ = 30.9 mm. The strength of the weld per mm thickness per mm length is 76 MPa.
A tension member splice is made with 14-inch E70 fillet welds as shown in Figure 5. Each side of the splice is welded as shown. All steel is A36. Determine the maximum service load, P, that can be applied if the live load to dead load ratio is 1.5. Note: Assume that the base metal shear strength is adequate (check the yielding strength for the gross area, fracture strength for the effective net area, weld strength and block shear strength). PL 5/8x8 4 in. Figure 5 2 PL 7/16x4