The connection is shown in Fig. 3. Two cover plates are applied to connect the steel plates by fillet welds. The dimensions of connection are presented in Fig. 3. The leg size of fillet weld hr is 10 mm. Q235 steel, f-215 N/mm2, E43 electrode, fw=160N/mm2. Calculate the load-carrying capacity of the fillet weld connection (Note: the strength of steel plate should be calcualted. (Unit: mm)

The connection is shown in Fig. 3. Two cover plates are applied to connect the steel plates by fillet welds. The dimensions of connection are presented in Fig. 3. The leg size of fillet weld hr is 10 mm. Q235 steel, f-215 N/mm2, E43 electrode, fw=160N/mm2. Calculate the load-carrying capacity of the fillet weld connection (Note: the strength of steel plate should be calcualted. (Unit: mm)

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.4.13P

See similar textbooks

Similar questions

Question 6 Two plates of Steel A72 Gr 50 are connected with each as shown in Figure 5. E70XX Electrodes were used and 7/16 in fillet weld were made by SMAW process. What is the design strength of the weld by LRFD and ASD? E10 in - 10in P, or P. - PLx 10 Figure # 4
a. Determine the design strength of a 1-in length of a 1/4-in fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength FEXX = 70 ksi. Assume that load is to be applied parallel to the weld length.b. Repeat part (a) if the weld is 20 in long.c. Repeat part (a) if the weld is 30 in long.
1. Design the fillet weld connection between the double equilateral angle steel and gusset plate shown in the figure. The steel is Q235B while the welding rod is E43, then the design value of weld strength f, is 160 N/mm², and the size of fillet weld hf is chosen as 8mm. If the axial force N = 1000KN, please calculate the effective lengths of the side fillet welds on both sides of angle steel under the condition of (1) two side welding is used, and (2) three side welding is used, respectively. t=12 N 2L125X10
7
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A flat bar used as a tension member is connected to a gusset plate. Size of weld is 6 mm, with an ultimate tensile strength of 185 MPa. E 70 electrodes Thickness of plate = 6.25 mm. Use ASD. Thickness of gusset plate = 9.5 mm. Fy = 248 MPa Fw = 0.60(485) Fu = 400 MPa Questions: The connected parts are of A-36 steel and assumed that the tensile strength of the member is adequate: a) Determine the strength of the connection per mm considering the design shear strength of the 6 mm fillet weld. b) Determine the base metal shear strength per mm. c) Determine the available strength of the connection.
The connection shows a PL10X200 loaded in tension and welded to a gusset plate 10mm thick. Calculate the following, assuming A992 steel is used. Use U =0.85. The weld thickness is ómm and the electrode is E70 (485MPA). PL 10 X 200 350mm What is the allowable weld connection strength (kN)?
A steel side plate is welded to a vertical steel column according to the specifications in Fig. 1. An E 70 welding electrode is used, and there is an applied load of F = 20 kN. %3D What weld size, s, is needed for a safety factor of 2 guarding against yield? F B, 150 C 100' - 200 Dimensions in millimeters Figure 1: Side plate welded to a vertical steel column.
A 180 mm x 90 mm x 10 mm angular section is welded to a gusset platehaving a thickness of 12 mm as shown in Figure ST - 100. An A 36 steel is used withFy = 248 MPa with an E70 electrodes fillet welds with Fu = 485 MPa. 1. Compute the value of P if the thickness( size ) of the fillet weld is 8 mm. 2. What is the minimum thickness of the fillet weld that can be used? 3. Compute the value of x if the thickness( size ) of the fillet weld is 8 mm.
Note:hand written solution should be avoided.
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A plate is attached to the frame of a machine by side fillet welds as shown in the figure. Determine the size of the welds to resist a vertical load of 150 kN. Assume that the allowable shearing stress at the throats of the weld is 145 MPa.
Please answer the problem attached image.(using Nscp 2015) thank you
THEORY OF STRUCTURES