Two 12 mm thick grade 350W steel plates, depicted in the figure below, are to be welded together using matching electrodes. Select the fillet weld size for the geometry shown if the applied factored tensile force is 400 kN. Confirm that the size selected meets the geometric requirements for fillet welds. 400 kN 100 60° 120 100

Two 12 mm thick grade 350W steel plates, depicted in the figure below, are to be welded together using matching electrodes. Select the fillet weld size for the geometry shown if the applied factored tensile force is 400 kN. Confirm that the size selected meets the geometric requirements for fillet welds. 400 kN 100 60° 120 100

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.4.5P

See similar textbooks

Similar questions

A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.
4.) A 150 x 90 x 12 angular section is welded to a gusset plate as shown in the figure. The angle is A36 steel with FY=248 MPa. The weld is E 80 electrode with Fu = 550 MPa. The allowable tensile stress for the angle is 0.6Fy and the allowable shear stress for the weld is 0.3Fu. The Area of the angular section is 2751 sq.mm. with y=51mm. CS 56 Which of the following most nearly gives the design force P? a.) 400,365.9 N b.) 409,348.8 N c.) 412,793.5 N d.) 420,366.6 N 5.) A W350 x 90 steel is used as a simply supported beam 8m long. The beam carries three equal concentrated loads at every quarter points. It also carries a uniform dead load o 5 kn/m (including its own weight) and a uniform live load of 7.20 kn/m. Properties of W 350 x 90 steel: bf = 250 mm The allowable bending stress is 0.66Fy. The allowable shear stress is 0.40Fy. The allowable deflection is L/360. Use Fx=248 Mpa and E=200 Gpa. tf = 16.40 mm V d = 350 mm Determine the maximum value of each concentrated load based on…
Situation 5. The angular section shown below is welded to a 12 mm gusset plate. Both materials are A36 steel with Fy = 250 MPa. The allowable tensile stress is 0.6Fy. The weld is E80 Electrode and 12 mm thickness. INNOVATIONS Properties of L 150x90x12: y = 50 shear stress of weld = 0.3Fu A = 2750 Allowable REVIEW INNOVATIE a K ➜ www A. 234 KN B. 349 KN b 13. What is the value of P without exceeding the allowable tensile the angle? C. 382 kN p. 413 kN 14. Find required length of the weld based on shear? A. 280 mm C. 300 mm D. 380 mm B. 320 mm 15. Find the required value of a? A. 108 mm B. 97.9 mm D. 185 mm NEW INNOVATIONS REVIEW INNOVATIOf REVIEW NEW INNOVATIONS
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A plate is attached to the frame of a machine by side fillet welds as shown in the figure. Determine the size of the welds to resist a vertical load of 150 kN. Assume that the allowable shearing stress at the throats of the weld is 145 MPa.
S Example 8.7 An ISA 200x100x10 angle LO 3 is welded to a steel plate by means of fillet welds as shown in Fig. 8.17. The angle is subjected to a static force of 150 kN and the permissible shear stress for the weld is 70 N/mm². Determine the lengths of weld at the top and bottom. 1₁ 150 kN TAILL Y2 200 12 - IG 100- 12 71.8 150 KN -10
b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm
Two plates are proposed to be jointed by welding as shown in the figure. Determine the size and length of the weld required to develop the full strength of the smaller plate which is 8 cm x 1.2 cm. Assume permissible tension in plate is 1500 kg/cm? and permissible shear in fillet weld is 1025 kg/cm. 8 cm) 12 cm
A double U-shaped butt weld is to connect two plates 200 mm (d) × 20 mm (b), as shown in the given figure. What is the stress developed in the weld if it is subjected to a moment of 10000 kN-mm? d=200 mm festbook b=20mm
THEORY OF STRUCTURES
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 100x100x10mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu=483.33 MPa. Fv = 0.30 Fu Questions: a) Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. b) Determine the length of side fillet weld required at the heel. c) Determine the length of side fillet weld required at the toe.
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
Please answer on the attached image