3A -> 5kip कोग र1ग

Q: A simply supported steel beam EVEN: 12m long carries a uniformly distributed load of 22KN/m load…

A:

Q: e section are given by the table. The beam is subjected to the concentrate the couple moment Mo…

A:

Q: Block properties: Length (L) = 134 mm Width (W) = 99 mm Height (H) = 60 mm E = 58 MPa V = 0.40…

A: Answer We are given Length L = 134 mm Width W = 99 mm Height H = 60 mm E = 58 Mpa ν = 0.40 σ1 = 26.4…

Q: Q.: Find the coordinate of the centriod of the shaded area 4 Y 3 m-

A: Given, Equation y=2x-30.5

Q: A C L- (2) B "1-12- -L/2→ C x

A:

Q: From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the centroid, (C),…

A:

Q: Locate the centroid for the area of a quarter circle shown.

A:

Q: Find the domains of: f(x)=- x - 9 a. {x\x€R, x#9} b. {x|x€R, x#-3, x#3} c. {x|x€R, x+-3, x # 3, x #…

A: Hello dear this is the solution of your problem The answer is found to be Option (b)  For…

Q: Virtual work Find 0 (slope @ point DJ D Find A (displacement point D) Draw moment diagram

A: A cantilever beam with AB portion having a moment of inertia as 7I and rest from B to E as I. A…

Q: Classify the following DE as Linear or Non-linear. 1. +5+ 6y = 0 d'y dx2 dx 2. +x2 dy + x³ dy – xe*…

A: To classify the given differential equations as Linear or Non-linear.   A differential equation (DE)…

Q: نقطتان )2( Shows polygon with the followng :Find the area (x,y) 2 1.8 1.6- 1.4- 1.2 0.8 0.6- 0.4…

A: answer is option a.)   Matlab command window picture is attached below

Q: What is D30 (or D10 or D 60)?

A: D10, D30, D60 refers to:D10 = particle size (diameter in mm) at which 10% of soil mass finer than…

Q: iv) If the specimen is loaded to a stress of 65 MPa and then unloaded, determine the residual…

A: From the figure, ( up to proportionality limit) σy=50 MPa∈y=0.002 Young's Modulus,…

Q: Locate the centroid y̅ of the area.

A: Draw the figure. From the figure, dA = y dx

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: Given: ● X ● x1 x1 = 15.35 mm . x2 = 16.74 mm x3 = 16.10 mm y1 = 19.32 mm y2 = 20.55 mm • y3 = 16.37…

A: Section diagram:

Q: PLATE NO.G 70KN 70KN →>>> T E 777777 1 35KN 9m PORTAL METHOD M LL B 6m N बैठ 9m 777777 4.8m 4.8m…

A:

Q: Y

A:

Q: Locate the centroid (x. y) of the cross-sectional area. 0.5 in. 4 in. 0.5 in. 3 in.

A:

Q: Prove that Ox - Oy sin 20 + Ty cos 20 and 『;-の cos 20 - Ty sin 20

A: The plane with maximum and minimum normal stresses is known as the principal plane. The shear stress…

Q: Draw the 3 Principal Views of the object (units in cm) 5.0 3.0 1.5 R=1.0 1.5 ↓ 1.0 3.0 -2.5 2.0

A: I have draw  Top view.  Front view

Q: Determine the maximum value of P (kN) without exceeding stress

A:

Q: Locate the centroid (x̅, y̅)of the following areas:

A:

Q: where does the 12 come from in "using the superposition" part?

A: This question is related to the Structural analysis from Civil Engineering.Given data - Beam with…

Q: Two designs for a beam are to be considered. Determine which one will support the loading shown…

A:

Q: 12.A swimming pool with plan and section shown in Fig. G is filled with water. It has two short…

A: Given:- d1=20 cm or 0.20 md2=20 cm or 0.20 cmC=0.80Plan area, A1=30×15=450 m2Tube area, A2=πr2=π0.12…

Highway Surveys and Location

Surveying is an operation in the civil engineering domain that requires collecting and identifying data regarding an area of land and topography. The data that is collected can be helped to plan and undertake the construction process. Civil engineers perform surveys to gather three-dimensional information regarding a particular area. Engineers specify several points on the surface of the earth and relationship between points, and the distance and angles between the points are evaluated. The data from this evaluation guides in drawing plans regarding buildings and structures.