* 2. Calculation question: Two side fillet weldingjoint, N=660 kN (static loading, design value),using angle steel with 2L 110×10. The thicknessof gusset plate is t1=12 mm, using the steel ofQ235B and electrode of E43, SMA welding.Determine the leg size hf and actual lengths oftwo welds.300N2L110×10t=12110

Answered: Image /qna-images/answer/dacdd801-f80d-4928-9bfd-cf145a44a7d4.jpg

Calculation question: Two side fillet welding int, N=660 kN (static loading, design value), sing angle steel with 2L 110×10. The thickness gusset plate is t1=12 mm, using the steel of 235B and electrode of E43, SMA welding.

Calculation question: Two side fillet welding int, N=660 kN (static loading, design value), sing angle steel with 2L 110×10. The thickness gusset plate is t1=12 mm, using the steel of 235B and electrode of E43, SMA welding.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Which products are semi-finished steels. I. Bloom II.Bars III.Rods IV.Billet V.Slab VI.Plates

A: Semi-finished steel is intermediate steel which is formed by casting liquid steel or by rolling and…

Q: give 8 examples of cold formed steel and state each of their uses or where can be seen or used

A: Cold-formed steel members are used additionally in bridges, storage racks, grain bins, car bodies,…

Q: Delermine the average normal stress in the aluminum due to this loading The A-36 steel pipe in…

A: Determine stress in steel and aluminium

Q: Two plates of Steel A72 Gr 50 are connected with each as shown in Figure 5. E70XX Electrodes were…

A: Given:- Steel A72Gr500 fillet weld=7/16 To find:- design strength by LRFD and ASD

Q: Use of mild steel instead of stainless steel can prevent corrosion. Select one: True False

A: Mild steel is more prone to corrosion whereas stainless steel is actually the steel which has…

Q: Situation 6: The lap splice shown will develop a full strength as shown in the figure. Us The width…

A: Data Given:Width of plate = 150mmThickness of plate = 12mmFy = 345To find out the size of weld by…

Q: Brass core (E = 105 GPa) Aluminum plates (E = 70 GPa) Rigid end plate 300 mm 60 ním 40 mm

A: Given data P = 500 KN h = 10 mm Need to find Stress in brass = ? Displacement of end plate = ?…

Q: O A fillet -welded joint of 6mm size is shown in the figure. the welded surfaces meet at 60-90…

Q: 2. The tensile link shown is flat, is 5 mm. thick, and carries an axial loac a. Compute the maximum…

A: GIVEN- Axial load (P)=1350 N Thicknesss (t)= 5 mm

Q: ---------------- is a relatively new technology that enables the complicated shaping of ultra high…

A: Hot stamping is a relatively new technology that enables the complicated shaping of ultra high…

Q: Using a lug angle, design a suitable riveted end connection for an angle ISA 100100,12 mm thick to…

A: Steel structures are formed by connecting available standard sections. Connections form an important…

Q: In a fillet weld, the direct shear stress and bending tensile stress are 50 MPa and 150 MPa…

Q: Problem #2: A plate constructed of ASTM A470-8 steel is loaded in tension (P=85 kN) when at room…

A: Given: a = 3 mm b = 35 mm t = 5 mm P = 85 kN ASTM A470-8 properties: Kc = KIc = 60 MPam Yield…

Q: Dynamic forces F1 = 4000N and F2 = 6000N are applied to the welded part shown in the figure as shown…

Q: rectangular plate of dimensions gure). The plate is subjected to a c -f 12.0 MPa in the short…

Q: Determine the modules of resilience of aluminum allow with yield strength of 40000 psi

Q: Two plates of dimensions 150 mm x 16 mm and 150 mm x 12 mm at their welding edges are joined by butt…

A: Given data- Plates dimensions- 150 mm×16 mm &150 mm×12 mm. Permissible tensile stress P =150…

Q: Two steel plates are lap jointed in a workshop using 6 mm thick fillet weld as shown in the figure…

A: Two steel plates are lap jointed in a workshop using 6 mm thick fillet weld The ultimate strength of…

Q: Two plates are connected by fillet welds of size 10 mm and subjected to tension, as shown in the…

A: Given:Load carried by both the weldsLoad carried by each weld.Constant that depends upon the angle…

Q: Answer the following questions for these TWO type of metals, (i) Steel 1050, and (i) aluminium…

A: Solution for Subpart b – For Steel 1050, the approximate ultimate tensile strength is fu = 690 MPa.…

Q: A) A specimen of alloy having the following engineering stresses produces the corresponding plastic…

A: Given :- To find :- Engineering stress corresponding to engineering strain of 0.4

Q: A Tension member with no holes is subjected to axial loads of PD=68kN & PL=64kN.It is also subjected…

A: A Tension member with no holes is subjected to axial loads of PD=68kN & PL=64kN.It is also…

Q: Experimental results show that in EBW the penetration depth of the weld decreases as the welding…

A: EBW stands for Electron Beam Welding, which is a high energy welding process that uses an electron…

Q: A 1 foot plate with a 0.25-inch thickness has a width of 2.4 inch and a hole at the middle with a…

A: W = 2.4 IN. t = 0.25 in. d = 2 in. Sut = 132 kpsi Sy = 84 kpsi

Q: For 4340 steel, the fracture toughness and yield strength depend on the prior heat treatment, as…

A: When a material is subjected to stress less than its yield stress, it will only experience elastic…

Q: Situation 1: The lap splice shown will develop a full strength as shown in the figure. Using E70 The…

A: d=39mm

Q: Which of the following failure will occur if plate edge preparation was not performed to the area…

Q: C) WHAT DOES QS CONTROL'S? D) WHAT DOES THIS MEAN'S ? ED HOW DO WE CALCULATE F) HOW DO WE CALCULATE…

A: CQs in the section controls for the strength of the welded sectionD this means minimum size of weld

Q: Two of the prevention methods to reduce a. Using mild steel Using inhibitors b. C. Reduce the…

A: An

Q: Pick the correct statement regarding welding. O a. More Noise during welding O b. Welding process is…

A: Given that: a. More noise during weldingb. Welding process is slowerc. 100%…

Q: Two plates, subjected to direct tension, each of 10 mm thickness and having widths of 100 mm and 175…

Q: Situation 5. The angular section shown below is welded to a 12 mm gusset plate.. Both materials are…

A: The given data is as follows : Size of angular section = 150 x 90 x 12 Area of angular section =…

Q: Reinforcing steel is used in structural concrete beams to withstand mainly compressive stresses.

A: True Hot rolled steel does not allow buckling of the member.Cold steel bars allow buckling partially…

Q: 20 mm 10 mm 10 mm 20 mm 10 mm 10 mm The Aluminum machine part is subjected to a bending moment M =…

A: Given M=75N.m To find Determine (a) distance of neutral axis from the bottom of the cross section,…

Q: uation 4: The lap splice shown will develop a full strength as shown in the figure. Using E70 el e…

A: I have solved your problem

Q: he double I-beam is fabricated by welding the three plates together as shown. Part A 50 mm 75 mm 20…

A: Shearing stress is defined as a type of stress that acts coplanar with the cross section of a…

Q: The threaded bolts A and B of the same material and length are subjected to identical tensile load.…

A: Given- Threaded bolts A & B, Same material & length, EA =EB PA=PB Length LA=LB, Strain…

Q: A flat bar used as a tension member is connected to a gusset plate. Size of weld is 6 mm, with an…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(1) Given A992 steel Ag = 10 in %3D KLy- 80, ry what is $ Pa=? = 60 the' column streugth design
98) What is another name for austenitic stainless steels?A) p91 steelsB) 18-8 steelsC) p92 steelsD) o1 steelsE) h11 steels 99) which is more important for assembly than its values?A) yield strengthB) hardnessC) sizeD) elastic modulusE) wear behavior 100) which is not one of the general properties shown by almost every metal?A) satietyB) high hardness and strengthC) good wear resistanceD) good thermal conductivityE) good electrical conductivity
For a tensile test it can be shown that the percent cold work (%CW) is related to strain according to the following relationship: %CW = () × 100 E+1 Using this equation, compute the percent cold work experienced by naval brass (for which the stress-strain behavior is shown in the Animated Figure 6.12) when a stress of 400 MPa (58020 psi) is applied. %CW
The cost of end anchorage steel compared to entire structural element is ____________ a) High b) Low c) Equal d) Zero
7. ASTM suggests a tolerance of... percent to allow the variation in strength as a test of ....w. water. A. 12 В. 8 C. 10 D. 15 E. 16 F. None of them
The equivalent stress for welding in given bracket connections would be if t = 5mm e i.e. Effective throat thickness of weld, use Fe410 steel and shop welding. P = 50 kN e = 200 mm h = 250 mm
128) With which test is the fluidity of metals measured?A. hardnessB. ViscosityC. CharpyD. SpiralE. Jominy 137) Which is not one of the alloying elements used in steel production? a) Molybdenumb) Aluminumc) Manganesed) Chromiume) Vanadium
A 2014-T6 aluminum tube having a cross-sectional area of 600 mm² is used as a sleeve for an A-36 steel bolt having a cross-sectional area of 400 mm², When the temperature is T=15 °C, the nut holds the assembly in a snug position such that the axial force in the bolt is negligible. If the temperature increases to T-80 °C and an axial force of 25 KN is applied to the assembly, determine the stresses in the bolt and the sleeve. Note: Length of the assembly is 150 mm, E is 200 Gpa, a is 12*106 (for bolt), E is 73.1 Gpa, a is 23*106 (for sleeve).
A . specimens geometry-5 is preferred when the end product is a thin plate or sheet إجابتك
Steel
Solve and determine the design strength of a 1 - in length of a 14- in fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength of 70ksi. Assume that the load is to applied parallel to the weld length.
For bolt grade 10.9 is used the steel of the yield strength equal to?