A fillet-welded joint is shown in the figure. The size of weld is 8 mm and safe stress in the weld is 110 N/mm2. What is the safe force (in kN) (to the nearest magnitude) to which the weld can be subjected? - 80 mm eunu 09-

A fillet-welded joint is shown in the figure. The size of weld is 8 mm and safe stress in the weld is 110 N/mm2. What is the safe force (in kN) (to the nearest magnitude) to which the weld can be subjected? - 80 mm eunu 09-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E = 29,000 ksi; a = 6.5x10-6/°F] bolts have a diameter of 0.30 in. The polymer [E = 370 ksi; a = 38.3x 10-6/°F] cylinder has an outside diameter of 6.6 in. and a wall thickness of 0.75 in. Assume a = 29 in. and b = 37 in. If the temperature of this assembly changes by AT = 135°F, determine: (a) the normal stress in the polymer cylinder. (b) the normal strain in the polymer cylinder. (c) the normal strain in the steel bolts. %3D %3D %3D %3D (1) C (2) a (1) b. Answer: (a) 02 = psi. (b) E2 = 3d (c) E1 =
A fillet-welded joint is shown in the figure. The size of the weld is 8 mm. Safe stress in the weld is 110 N/mm². What is the safe force (to the nearest magnitude) to which the weld can be subjected? 80 mm 60 mm
Given the compound bar below, determine the maximum allowable value of P if the change in length of the bar is limited to 5.67mm. The bar properties and allowable stresses are given in the table below. (answer in N)
(b) (ii) A 20 mm diameter rod made from 0.4% C steel is used to produce a steering rack. If the yield stress of the steel used is 350 MPa and a factor of safety of 2.5 is applied, what is the maximum working load that the rod can be subjected to? 2
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A plate is attached to the frame of a machine by side fillet welds as shown in the figure. Determine the size of the welds to resist a vertical load of 150 kN. Assume that the allowable shearing stress at the throats of the weld is 145 MPa.
A mild steel bar having 300 mm dia is subjected to shear stresses yielded at a stress of 250 MPa. The maximum value of torque iskNm that can be applied if factor of safety of 1.8 is to be provided.
The assembly consists of two A992 steel bolts AB and EF and an 6061-T6 aluminum rod CD. When the temperature is 30°C, the gap between the rod and rigid member AE is 0.1 mm. Assume BF is also rigid. (Figure 1) Figure 400 mm A B 25 mm 50 mm D 0.1 mm 300 mm E 1 of 1 25 mm Part A Determine the normal stress developed in the bolts if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. of = Submit Part B σ₁ = Submit O HA Value Request Answer Provide Feedback ■μÅ Value Determine the normal stress developed in the rod if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units Request Answer wwwww Units ? wwwww Review ? Next >
2- The Tensile stress of AISI 1035 Cold-drawn steel is; (a) 550 MPa. (b) 500 MPa. (c) 450 MPa.
Prblm -6.