The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this 640 sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (ay) MPa, and for the bronze (ay)or 520 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. E 200 GPa, E= 100 GPa. 10 mm 20 mm

The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this 640 sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (ay) MPa, and for the bronze (ay)or 520 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. E 200 GPa, E= 100 GPa. 10 mm 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A fillet-welded joint is shown in the figure. The size of the weld is 8 mm. Safe stress in the weld is 110 N/mm². What is the safe force (to the nearest magnitude) to which the weld can be subjected? -80mm- 60 mm
A fillet-welded Joint of 6mm size is shown in the figure. The welded surfaces meet at 60-90 degree and permissible stress in the fillet weld is 108MPa. The safe load that can be transmitted by the joint is 100mm 50mm
Calculate the shear yield stress (ksi) of A588 steel.
Two steel plates are connected by a pair of splice plates with eight bolts as shown. The ultimate strength of the bolts is bolts is 270 MPa. An axial tension load of P = 480 kN is transmitted by the steel plates. If a factor of safety of 1.6 with respect to failure by fracture is specified, determine the minimum acceptable diameter "d" for the bolts. %3D P. splice plate steel steel plate plate (2) (1)
Find the value of p
A fillet-welded joint is shown in the figure. The size of the weld is 8 mm. Safe stress in the weld is 110 N/mm². What is the safe force (to the nearest magnitude) to which the weld can be subjected? 80 mm 60 mm
An A36 steel plate with width of 400 mm and thickness of 12 mm is to beconnected to a plate of the same width and thickness by 34 mm diametersbolts, as shown in the figure (next slide). The holes are 2 mm larger thanthe bolt diameter. The yield strength of the steel plate is Fy = 248 MPa.Assume allowable tensile stress on net area is 0.60Fy. It is required todetermine the value of b such that the net width along bolts 1-2-3-4 isequal to the net width along bolts 1-2-4.a. Calculate the value of b in mm.b. Calculate the value of the net area for tension in plates in mm².c. Calculate the value of P so that the allowable tensile stress on net areawill not be exceeded.(Use at least 2 decimal points on your answers.)
The assembly consists of two red brass C83400 copper rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rod EF of diameter 40 mm, and a rigid cap G. The supports at A, C and F are rigid. Modul of elasticy for the copper is Ecopper = 101 GPa. Modul of elasticity for the steel is Esteel = 193 GPa. (Figure 1) Figure ▼ Part A σAB = Submit Part B Value Submit μÀ Request Answer Part C LO OCD = Value Determine the average normal stress developed in the rod AB. Express your answer to hree significant figures and include the appropriate units. μA Request Answer EF = Units Units A μÃ -300 mm- Value C 30 mm Determine the average normal stress developed in the rod CD. Express your answer to three significant figures and include the appropriate units. Submit Request Answer 30 mm ? B D G ? E 450 mm 40 kN 40 kN 40 mm Determine the average normal stress developed in the rod EF. Express your answer to three significant figures and include the appropriate units. Units F ? < 1 of 1
Given the compound bar below, determine the maximum allowable value of P if the change in length of the bar is limited to 5.67mm. The bar properties and allowable stresses are given in the table below. (answer in N)
Problem 4 Given two welded plates n A36 plates t= 3/ • fillet size w=1/4" Electrode Fexx= 70 ksi • plate width = 9" ● ● ↑ t=¾/2" = 2) = Pu= smaller of (1) A(2) w=1/4" Base Metal Strength, DRn is given by: ÞRn = 0.75(0.6Fu) (tBM)(Lw) t=3/8" Determine max Pu that can be applied to this connection ? hint: Dobtain Pue based on weld strength (transverse) BM strength = where tbm = thickness of the thinner connected plate Lw= length of the weld Fillet weld this side only i.e. lw= 9 in کہ ۔ Ри opy
What is the manufacturing tensional yield strength (lbf) of grade S135 drill pipe? a. This is a trick question because drill pipe size is not provided b. The answer can’t be calculated because the length of the pipe is not given c. The yield strength is 135000 psi and is a property of the steel d. The yield strength is 135000 psi and depends on the cross-sectional area
PLEASE ANSWER THIS QUESTION ASAP!!!