The assembly is used to support a 10 kN point load at the tip as shown. The steel rod has a diameter of 12 mm, and the steel pins each have a diameter of 8 mm. T wooden bar ABC has a height of 100 mm and a thickness of 40 mm. Taking yiel stress in tension and shear for steel of oy=480 MPa and ty=270 MPa, respective and tensile strength of 17 MPa for the wood, determine (a) The factor of safety of the steel rod BC (b) The factor of safety of pins at B and C (c) The factor of safety of the wooden bar ABC (d) The bearing stress at pin A. Steel rol. 12 an 1.5. Wael inber 100 me

The assembly is used to support a 10 kN point load at the tip as shown. The steel rod has a diameter of 12 mm, and the steel pins each have a diameter of 8 mm. T wooden bar ABC has a height of 100 mm and a thickness of 40 mm. Taking yiel stress in tension and shear for steel of oy=480 MPa and ty=270 MPa, respective and tensile strength of 17 MPa for the wood, determine (a) The factor of safety of the steel rod BC (b) The factor of safety of pins at B and C (c) The factor of safety of the wooden bar ABC (d) The bearing stress at pin A. Steel rol. 12 an 1.5. Wael inber 100 me

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The two wooden boards are connected by a 0.7 in. diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D = 2.4 in. and d = 0.8 in. The nut is tightened to cause a tensile stress of 12000 psi in the bolt. Determine the bearing stress between the washer and the wood. Answer: Ob = i Bolt D Washer psi - Washer Nut
A steel cantilever beam is fabricated from two structural tees welded together, as shown in the figure. For this beam, the allowable bending stress is 150 MPa, the allowable shear stress of the steel is 100 MPa, and the allowable shear flow along the weld is 2MN/m. Determine the allowable force P that the beam can carry. (All dimensions are in mm).
SOLVE COMPLETELY. SHOW COMPLETE SOLUTION, INCLUDE FBD
The assembly consists of two posts AD and CF made of steel and having cross- sectional area of 1000 mm², and an aluminium post BE having a cross-sectional area of 1500 mm². If a central load P is applied to the rigid member ABC, determine the normal stress in each post. Take elastic modulus of steel and aluminium as 200 GPa and 70 GPa, respectively. PKN P [kN] -0.5 m- Last digit of Student ID 0, 1, 2, 3, 4 5,6,7,8,9 500 700 e.g. SID 21051234 P=700 A B -0.5 m C 0.4 m F Fig. 1-1 System with three posts Last digit
Problem 3 (20 minutes) The bars' assembly has the dimensions, diameters and materials indicated (EST 29,000 ksi; EBR = 15,000 ksi). The assembly is fixed at one end and has D in, E = 1. 10 in and F20 kip. Determine the normal force N in the bronze and the steel = d=2in = 30 d= 1 in F(kip) BRONZE ← STEEL A B ↑ c D(in) Elin 2. Draw the normal force diagram along the assembly 3. Determine the elongations ALAB (of portion AB), ALBC (of portion BC) and ALAC
Mechanics of Deformable Bodies L T The wooden bar consists of two segments, each of length L. One segment has a square cross section of width d, the cross section of the other segment is a circle of diameter d. The working stress for the wood is tw=5MPaand the shear modulus isG=0.5GPa. Using L=0.6m and d=50mm, determine (a) the largest torque T that can be safely applied; and (b)the corresponding angle of twist for the bar.
For the given properties of beam below. Design the reinforcements of the beam. d'=75 mm b=400 mm d=580 mm fc'=35 MPa fy=320 MPa Mu=1000000000N mm Input is 0 in As' if compression bars are not needed. A. USE NSCP 2001, As = mm2, As' = mm2 B. USE NSCP 2015, As = mm2, As' = mm2 %3D
Determine the length of tension anchorage required for the 36 mm diameter plain mild steel reinforcing bars in the canrilever of figuer below. The charactersitic material strengths are feu-30N/mm² and fy=250KN. The ultimate anchorage bond stress. Stress, fou-1.5N/mm² Anchorage length R25 bars
From Steel Design Topic Include complete solution
The question is below.
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
Load P is applied to joint D and the temperature increases by 50 °F. There are two steel (E = 29*10^6 psi; a = 6.5*10^-6/°F) AD and DC and a bronze (E = 16*10^6 psi; a = 9*10^-6/°F) BD with a length of 50 inches. Each bar is a 0.75 inch diameter. Find the deformation of every rod, the displacement at D, and the stress in each rod.