Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 1200 mm² A = 900 mm² P, Pa B C D mm-350 mm 500 mm -250 A

Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 1200 mm² A = 900 mm² P, Pa B C D mm-350 mm 500 mm -250 A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three plates are welded together to form the section shown. Dimensions of the cross section are b = 6.0 in., d = 18.0 in., a = 3.3 in., and t = 0.8 in. For a vertical shear force of V = 45 kips, determine the shear flow through the welded surface at B.
5. The column shown in the figure is reinforced with 8 28mm diam steel with fy = 414Mpa and f'c = 21Mpa a. What is the nominal balanced load and balanced eccentricity? b. Fing pn if e = 220mm c. Find pn if e = 550mm d. Find pn when the stress in tension steel is 180Mpa 60 mm 60 mm 550 mm 650 mm CD Pn
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 5.5 in., d = 16.5 in., a = 3.4 in., and t= 0.8 in. For a vertical shear force of V = 48 kips, determine the shear flow through the welded surface at B. В b Answer: 9B = i kip/in.
7
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 5.1 in., d = 15.3 in., a = 3.6 in., and t = 0.8 in. For a vertical shear force of V = 40 kips, determine the shear flow through the welded surface at B. y d Ta b. Answer: kip/in.
The outer diameter of the bronze pipe flush-mounted at the A and B points is given as D and the wall thickness as s. The pipe is tightened at the C point with a pipe wrench. Determine the greatest torsional stress that will occur in the pipe.D=11mm y=3mm F=140N
A solid 1.20 in. diameter shaft is subjected to a torque of T = 230 lb-ft and an axial load of P = 6500 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1= i %p2 = i A Tmax in-plane = i H Save for Later (1) psi psi T B psi (b) Show the stresses of part (a) and their directions on an appropriate sketch. eTextbook and Media Attempts: unlimited Submit Answer
For problem solving, round intermediate answers to hundred thousandths (five decimal places) and final answers to the nearest thousandths (three decimal places) and DO NOT forget to affix their corresponding units
a. The beam of the cross section shown below has f'c = 3000 psi and f₁ = 60,000 psi. Neglect the tensile strain check and As,min check. Calculate Mr. b. Same cross section as part (a) but the steel is changed to four No. 10 bars. Calculate Mr. Calculate the percent increase in M, and As. c. Same cross section as part (a) but the depth d is increased to 28 in. Calculate Mr. Calculate the percent increase in M, and d. n d. Same cross section as part (a) but f'c is increased to 4000 psi. Calculate M. Calculate the percent increase in M, and f'c. n e. For the same cross section verify that the tension steel yields. S For 4#9, A = 4.00 in.² and for 4#10, A = 5.08 in.² S 16" 4-#9 24"
The allowable stress is allow = 22.4 ksi. (Figure 1) Figure Part A P = μÃ 0.25 in. Value 5 in. 1 in. 0.25 in. Determine the maximum axial force P that can be applied to the steel plate. Express your answer to three significant figures and include the appropriate units. -0.25 in. kip 2.5 in. ? 1 of 1
1 - A bronze rod 3 m long with a cross sectional area of 320 mm? is placed between two rigid walls as shown in Figure. At a temperature of -20°C, the gap A = 1.5 mm. Find the temperature at which the compressive stress in the bar will be 35 MPa. Use L= 3, a = 18.0 × 106 m/(m-°C), and E = 80 GPa. (10 Points) A
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of thewhole structure which is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94