two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm. Knowing that beam is subjected to V 5000 N, and that the moduli of elasticity for steel and wood are 200 and 40 GPa, respectively. Determine: (a) Shearing stress in cach bolt; and (b) shearing stress at the mid- height of the upper steel plate. 12 m Solution:- 19 wm

two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm. Knowing that beam is subjected to V 5000 N, and that the moduli of elasticity for steel and wood are 200 and 40 GPa, respectively. Determine: (a) Shearing stress in cach bolt; and (b) shearing stress at the mid- height of the upper steel plate. 12 m Solution:- 19 wm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please help me to design a simple tensile structure for the exhibition space roof
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
PLEASE ANSWER ASAP! RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). 20 IN-m Sm stcel hellw circalar duminum Selid circular D= 75 mny Do- IDO mn D> 80 mm G- D GPon 6- IS0 EPa
Please answer within 5 minutes
The two wooden boards are connected by a 0.7 in. diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D = 2.4 in. and d = 0.8 in. The nut is tightened to cause a tensile stress of 12000 psi in the bolt. Determine the bearing stress between the washer and the wood. Answer: Ob = i Bolt D Washer psi - Washer Nut
Show complete and detailed solution. Draw illustrations
SOLVE THIS PROBLEM USING THE SLOPE DEFLECTION EQUATIONS: A bolted connection shown is connected by 20 mm diameter bolts with an edge distance of 50 mm and the distance center to center of holes to be 75 mm. Assume that the deformation at bolt hole is a design consideration. The bolted connection is carrying an ultimate load Pu = 1500 kN, Fy = 248 MPa, Fu = 400 MPa and Fn = 415 MPa. Determine the following: (1) Design bearing strength of one bolt. (2) Design shear strength of one bolt. (3) The number of bolts are required for the connection show. P 12 mm plase P= I S00 kN 18 mm platr 12 mm plate
3- Determine: m 0.4m a) The stresses in the bars shown after a temperature rise of 96°C. Brone har Ahunknan bar A-1500man A-1500mm E-10SGPa E-TGP -21.6 21 b) the corresponding change in the length of the bronze bar.
The T-beam has the following properties: flange thickness = 125 mm flange width = 1000 mm web width = 500 mm web height = 350 mm f'c = 28 Mpa a) Calculate the stresses in concrete at uncracked stage under 200 kN-m. b) Calculate the cracking moment. c) Determine the balanced steel area and balanced ultimate moment. The steel is placed 80 mm from its cg up to extreme fiber with yield strength of 414 MPa.
A double channel shape is used as a tension member. The channels are bolted to a 10 mm gusset plate with 22 mm diameter bolts. | 75 75 75. /channel (12.18 mm thick) 50 50 100 -T 50 gusset plate (10 mm thick) Yield strength for tension member = 345 MPa Yield strength for gusset plate = 248 MPa Ultimate tensile strength Fu = 400 MPa for gusset plate Fu = 450 MPa for channel Properties of 1 channel A = 3555 mm² tw = 12.18 mm Reduction factor, U = 0.90 Determine the allowable tensile strength of the tension member (channel) based on its net area. (kN)
The working load P on the propped cantilever shown are each 150 kN. If the yield stress of mild steel is 300 MPa, determine the plastic section modulus in cubic millimeters, using a load factor of 1.75 against collapse. (express your response this way, x,xxX,XXX.X). Pu Pu 1.1 2m B A 2m 2m