4. Determine the maximum load P that can be applied in the system consisting of a bent bar bolted at both ends through the fiberglass as shown. The diameter of the bent bar is 1/4" Ø, outside diameter of the washer is 7/8" Ø and the thickness of the fiber glass is 3/8". The working shear stress between the fiberglass and the washer is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi. Use 2 decimal places in every solved value. bent bar fiberglass washer bolt cap 7 8. 8. 1/14

4. Determine the maximum load P that can be applied in the system consisting of a bent bar bolted at both ends through the fiberglass as shown. The diameter of the bent bar is 1/4" Ø, outside diameter of the washer is 7/8" Ø and the thickness of the fiber glass is 3/8". The working shear stress between the fiberglass and the washer is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi. Use 2 decimal places in every solved value. bent bar fiberglass washer bolt cap 7 8. 8. 1/14

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

axial compressive force P. If the stress on steel snugly fitted on a solid steel rod of 20 mm A tube of aluminium of 40 mm external diameter and 20 mm internal diameter diameter. The composite bar is subjected to a bar is 70 N/mm", the stress in the aluminium tube and corresponding value of P will be: E for steel: 2 x 10 N/mm and E for aluminium 7 x 10ʻ N/mm')
The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
Current Attempt in Progress A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E = 29,000 ksi; a = 6.5x10-6/F] bolts have a diameter of 0.35 in. The polymer [E = 370 ksi; a = 37.2x 10-/°F] cylinder has an outside diameter of 6.9 in. and a wall thickness of 0.65 in. Assume a = 28 in. and b = 34 in. If the temperature of this assembly changes by AT = 130°F, determine: (a) the normal stress in the polymer cylinder. (b) the normal strain in the polymer cylinder. (c) the normal strain in the steel bolts. (1) (2) (1) b. Answer: (a) 02 = psi. (b) €2 = (c) E1 = Save for Later Attempts: 0 of 1 used Submit Answer NWP Assessme. NWP Assessme. O ManyCam Desktop 30°C
What maximum load P can be applied without exceeding an allowable stress of 70 MPa for aluminum or 120 MPa for steel? Can a larger load P be carried if the length of the aluminum rod is changed. the length of the steel portion being kept the same? If so, determine this length
Please show a detailed solution and explanation including its FBD. Thank you!
A 1.65m long rod with a circular cross-section is subjected to a tensile load of 50 kN. The rod is made from AISI 1040 hot-rolled steel. The allowable tensile stress is 165 MPa. The rod is permitted to elongate up to 7mm without causing any issues. The proportional limit for the steel is 180 MPa. (A) Compute the required area necessary to meet the stated requirements based on allowable stress. Express your answer in square millimeter units as an integer. (B) Compute the required area necessary to meet the stated requirements based on allowable elongation. Express your answer in square millimeter units as an integer.
Round off final ans only, dont round initial values
Use the giuven values: Aluminum: E = 10 x 106 psi, α = 12.8 × 10-6 in/(in·°F) Bronze: E = 12 x 106 psi, α = 10.5 × 10-6 in/(in·°F) Show you complete solution.
Show full solution
A rectangular steel block is 3.2 inches long in the x-direction, 2.9 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 48 kips tension in the x-direction, 65 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
What is the manufacturing tensional yield strength (lbf) of grade S135 drill pipe? a. This is a trick question because drill pipe size is not provided b. The answer can’t be calculated because the length of the pipe is not given c. The yield strength is 135000 psi and is a property of the steel d. The yield strength is 135000 psi and depends on the cross-sectional area
A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 50 kips tension in the x-direction, 60 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places