4. Determine the adequacy of members AB and BC. Use W14x53 and A-36 steel. The service load P-250 kN. Assume k = 0.85. A 5m 3m 3m 3m

Q: What are the disadvantage of steel sheeting?

A: The disadvantage of steel sheeting are as follows:

Q: What metal is the main ingredient in steel?

A: Given : steel…

Q: In steel design, if the term is available strength   Is it LRFD OR ASD and explain why? Thank youu

A: The LRFD method and ASD method are two primary methods used in structural engineering for designing…

Q: What is classification scheme for composite materials ?

A: Brief concept introduction- Composite Material- These materials are made up of two or more materials…

Q: How we Innovative techniques in repair and strengthening of concrete structures. (FRP Wrapping)

A: The process of repairing concrete is very difficult. Deterioration is brought on by a wide range of…

Q: Describe about the spun-bonded process?

A: Spun-bonding:

Q: #5.) GIVEN: FIND: Ix of the composite shape 12x30

A: To Determine Moment of Inertia of the composite shape about Centroidal x-axis.

Q: 2. Discuss how structural steel is tested in the aboratoryforquality contro. Cite relevant ASTM…

A: Different tests, including destructive as well as nondestructive, are carried out to describe the…

Q: how possible designs of welded joints in structural steel design

A: Solution: The assumption for the weld Design:1. Welds are Homogeneous and isotropic.2. Connected…

Q: Why do you need to accurately identify the size, type and grade of steel?

A: -Steel is the general term of a large family of iron–carbon alloys, which are made by malting under…

Q: Explain the purpose of each part of the AISI steel designation code?

A: AISI steel designation code:

Q: Define the  various limit states of strength ?

A: Answer:- Limit state:- A limit state is a condition of a structure beyond which it no longer…

Q: Define The ultimate strength design method

A: The ultimate strength design method: There are three design methods: 1.Working stress…

Q: What are the commonly used fastening methods for joining structural steel members?

A: Fastening of the steel structure joint is done by using following type of connections- Rivetted…

Q: How can flaws in steel and welds be detected? Discuss the concept of a nondestructive test used for…

A: During production of steel and during process of welding, many factors may cause defect on…

Q: Distinguish between hardening and setting?

A: Brief concept introduction- Hardening and setting are the terms related to the cement.

Q: inum specify

A: solution of above problem is below:

Q: With supporting examples, what are the three most commonly used rolled structural steel shapes and…

A: Required: Most commonly used rolled steel structure and where they are used.

Q: How to increase the steel resistance to corrosion?

A: Steel corrosion can be defined as an electrochemical process that occurs in the presence of oxygen…

Q: How to determine the size, number, spacing and location of the flexural and temperature…

A: Answer:- Reinforcing bar: Reinforced concrete in modern days widely used versatile composite…

Q: The following data are from a research project. Determine the yield strength, ultimate strength, and…

A: From the given graph ultimate strength, yield strength and elongation can be found

Q: Create a flowchart of modern steel making process and describe each process

A: Steel is an alloy of iron with some percent of carbon. The steel contains less than 2% carbon, 1%…

Q: Based from color, what is the major indicator wether a reinforcing steel bar is weldable or not?

A: There are a few ways to tell the difference between grades of steel rebar. One of the easiest is to…

Q: What are the commonly produced cast irons?

A: Cast Iron Cast Iron is an alloy of iron that is composed of 2% to 4% of carbon content and different…

Q: A 150 mm x 90 mm x 12 mm angular section is welded to a gusset plate as shown. Area of the angle is…

A: Area of the angle = 2736 sq.mmallowable shear= 150 MPaFt= 0.6FyFy= 250 MPa

Q: Discuss Selection and Sizing of Anchor Bolts

A: Solution: When anchoring, the general rule is that the embedded depth  should be at least 4 diameter…

Q: methods to protect steel tension members from rust and corrosion.

A: These members are subjected to axial tensile forces.These forces try to elongate the members.

Q: Q- IF THE LENGTH OF THE WELDED JOINTS FOR TWO PLATES IS 700 MM FOR A PLATE OF 8 MM AND 10 MM WELDED…

A: Given- Length of welded joints=700 mm,plates thickness 8 mm & 10 mm,weld size= 6 mm. It is…

Q: factor which affect splitting tensile strength and flexural strength .

A: The most common and basic factor which effect split tensile strength and flexural strength is:

Q: What is the difference between cast iron and steel?

A: CAST IRON: Iron is an element that exists in natural forms and around 4% of carbon in iron makes it…

Q: Question 1[ a) What is a truss? Explain shortly in your own words, and illustrate with one example.…

A: a) What is a truss? Explain shortly in your own words, and illustrate with one example. b) For the…

Q: Q: Identify the steel grades specified for each structural steel standard (ex: ASTM A36, ASTM A992)

A: Here are the common steel grades specified by some common structural steel standards: ASTM A36:…

Q: Differentiate how to test welded from tension joints

A: Why do we need a welding test? An error in the welding process may damage weld metals significantly…

Q: Explain the design procedure of the welded connection

A: question related to the steel structurelet's discuss the design procedure of the welded connection

Q: identify a grade of steel, what would u choose?

A: The best grade of steel which i choose would be Fe500, because it as high yield strength compared to…

Q: why do the surfaces of reinforcing bars have rolled-on deformation?

A: Answer Since Reinforcing bars are provided in concrete to increase ductility of concrete structure…

Q: What are splices? Give and discuss the types of splices in reinforcing steel.

A: Brief concept- Splices- It is used in the construction to join the reinforcement bars. Splicing…