Situation No. 2 A bronze bar is fastened between a steel bar and an aluminum bar as shown below. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel Bronze Aluminum A = 480 mm? A = 650 mm A = 320 mm 3P 4P 2P 1.0 m 2.0 m 1.5 m

Situation No. 2 A bronze bar is fastened between a steel bar and an aluminum bar as shown below. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel Bronze Aluminum A = 480 mm? A = 650 mm A = 320 mm 3P 4P 2P 1.0 m 2.0 m 1.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Read the question carefully and give me right solution according to the options
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa If the allowable strain for both materials is 0.0005, which of the following most nearly gives the maximum load the member can carry so that this allowable strain is not exceeded? Select the correct response 162.00 kN 185.00 kN 205.00 kN 175.00 kN
FN= 119 mPa, SN= 93MPa. provide fbd
Draw a typical stress–strain relationship for steel subjected to tension. On the graph, show the modulus of elasticity, the yield strength, the ultimatstrength, and the rupture stress.
Show Stress/ strain curve for nitinol and steel (2 separate charts please)
An unstiffened web I-section fabricated from a 10 mm thick plate by fillet welding as shown in the figure. If yield stress of steel is 250 MPa, the maximum shear load that section can is take is [2 Marks] 10 mm 300 mm 10 mm 200 mm
QI/ An aluminum bar carries the axial loads at the positions shown in Fig. 1, below. The diameter for part AB, BC and CD is 35 mm, 40 mm and 30 mm, respectively. The elastic modulus for aluminum is 72.4 x 10 N/mm. Determine the internal stresses at section (A-B), (B-C) and (C- D), and the elongation (AL) in length at each part of aluminum due to loading. в D 37 kN 10 kN 45 kN 18 kN 1000 mm 800 mm I 600 mm Fig. 1
What do you call the stress caused by the application of couple in the material?
A fillet-welded joint is shown in the figure. The size of the weld is 8 mm. Safe stress in the weld is 110 N/mm². What is the safe force (to the nearest magnitude) to which the weld can be subjected? 80 mm 60 mm
#4 will upvote to anyone who will answer
Sketch a sample stress-strain behavior of steel and identify different levels of strength.
When designing a structural member, which of the following statements is FALSE? Select one: A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is.