5. Find the allowable strength of the welded connection with a minimum throat size shown below. Base metal: S275 Fy = 275N/mm² Fu = 430N/mm² Weld metal tensile strength: Fe = 480N/mm² [all dimensions are in mm] -10mm thick gusset plate 150 125 125 -10mm thick gusset plate 125 VIEW A-A a 125 PL 150x12 PL 150x12 -PL 150x12 A

5. Find the allowable strength of the welded connection with a minimum throat size shown below. Base metal: S275 Fy = 275N/mm² Fu = 430N/mm² Weld metal tensile strength: Fe = 480N/mm² [all dimensions are in mm] -10mm thick gusset plate 150 125 125 -10mm thick gusset plate 125 VIEW A-A a 125 PL 150x12 PL 150x12 -PL 150x12 A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.
Problem 5: The lap connection shown consists of a PL1/2"X3" plate connected to a ½ in gusset plate with ¼" longitudinal fillet welds as indicated. The plates are A36 steel and the electrodes are E70XX. Calculate the length L (in) of the connection to develop the full capacity of the plate. Hint: The full capacity of the plate will depend on the governing strength of the tension member. Neglect block shear. Use ASD 6" x 1/2" P [ T L 1/4 1/4 E70 - 13²x P 3" x 1/2"
10 mm fillet welds Determine the design capacity of the welded lap steel connection shown below. All steel plates are 50X10mm dimension. Both fillet welds are 10mm E48XX SP, continuous across the full plate width. If the connection was tested to failure, which component would fail first.
Given: The L8x4x½ shown below is welded to the gusset plate by its long leg. L₁ = 10" and L₂ = 7.5". L₁ L₂ Determine the gross area. 5.80 in² Calculate the length of the connection. 8.75 Calculate the eccentricity of the connection. 0.854" Calculate the width of the connected element. Calculate the value of the shear lag factor. Calculate the effective net area. in² II
Provide a balanced welded connection to mobilize the full capacity of the angle. ( Filler material :fy = 480 MPa, fu = 560 MPa, Members are S235) a Section a-a 10 mm 10 cm P { =37.14 mm 5 cm 16 mm Gusset Plate a
Assume that the gusset plate and welds are satisfied. A gap allowance of 1/16 inch is to be considered to fit the gusset plate in the HSS. The steel used in the tension member is ASTM A500 Grade C HSS 6 x 0.5 with a length of 30 feet. a.) Find the shear lag factor b.) Find the Effective net area (Ae) c.) Solve for the tensile strenngth 16-inch-long fillet weld HSS 6 x 0.5 1/2 in. thick gusset plate 17 inch long
The connection shown consists of two, grade A307, M16 bolts in standard holes. The bolts are snug-tight and threads are permitted in the shear planes. Deformation around the bolt holes is a design consideration and the bolt spacing is as indicated. The 6.35 mm thick plates material are made of A36 steel. Which of the following most nearly gives the nominal bearing (considering also the tearout) strength of the bolts? CHOICES:a) 192 kNb) 384 kNc) 268 kNd) 195 kN
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm
A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x 6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer
A tension member splice is made with 14-inch E70 fillet welds as shown in Figure 5. Each side of the splice is welded as shown. All steel is A36. Determine the maximum service load, P, that can be applied if the live load to dead load ratio is 1.5. Note: Assume that the base metal shear strength is adequate (check the yielding strength for the gross area, fracture strength for the effective net area, weld strength and block shear strength). PL 5/8x8 4 in. Figure 5 2 PL 7/16x4
A PL3/8"X6" tension member is welded to a gusset plate as shown in the figure. The steel specification is ASTM A36. Assume that and compute the following: a) The design strength per LRFD b) The design strength per ASD PL ¾ x 6