1. A riveted lap joint is shown in the figure below. The rivets used are A502, Grade 2, hot-driven with diameter of 16mm. The steel is ASTM A501, 200mm wide and 10mm thick. Determine the safe value of P in all possible modes of failure and the allowable and ultimate value of P that the connection can resist. Use NSCP 2015 110 mm 10 mm

1. A riveted lap joint is shown in the figure below. The rivets used are A502, Grade 2, hot-driven with diameter of 16mm. The steel is ASTM A501, 200mm wide and 10mm thick. Determine the safe value of P in all possible modes of failure and the allowable and ultimate value of P that the connection can resist. Use NSCP 2015 110 mm 10 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

20mm Steel Plates in the figure shown are connected by 9 rivets with 20mm diameter. If the Allowable Shear stress for the rivet is 194 MPa and Allowable stress for bearing on the plate is 234 MPa, what is the maximum load P that can be applied in the connection?
Shown in Figure 1 is a centrically loaded bolted connection. The diameter of the bolts is 19 mm while holes have 21 mm diameter. Use depth 4y = 200 mm. 1. Determine the critical net width (Net Width) for the staggered bolted connection as shown in the figure. 2. Determine the value of "x" so that the net width along bolts A-B-C-D-E is equal to the net width along bolts A-B-D-E.
A double cover butt joint is shown in figure 2 below. If the steel is Grade S355JR and the bolts are M20 Grade 8.8 S, determine the strength of the connection. Assume the contact surface of the bolts are blast – cleaned with Class B coatings. The connection is required not to slip at serviceability. 80 120 80 80 120 80 -13 All dimensions are in mm Figure 2: Double cover butt joint. 300 O O O O o o O o o
Which of the following is true of slip-critical type connections? O Load is transferred by sehar O Load is transferred by bearing of bolts against the hole O Load is transferred by moment O Load is transferred by the friction resistance of the connected parts
Please answer the questions with a complete solutions. Thank you.
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
If the thickness of plate to be connected by a rivet is 16 mm, the suitable size of rivet will be (a) 16 mm (c) 24 mm (b) 20mm (d) 27 mm
10 mm fillet welds Determine the design capacity of the welded lap steel connection shown below. All steel plates are 50X10mm dimension. Both fillet welds are 10mm E48XX SP, continuous across the full plate width. If the connection was tested to failure, which component would fail first.
If the design tensile strength Phi Pn of a tension member is controlled by rupture failure. Which of the following actions will NOT increase its capacity? using welds instead of bolts using larger cross section of the member increasing strength of steel using thicker gusset plate
130% v - + 7 Annotate T| Edit Trial expired Unlock Full Version ENGR 263 A A A EXERCISES Eleven sets of illustrations and the corresponding free-body diagrams of building-related beams were provided in Chapter 4 as Exercises 4. I through 4.11. These free-body diagrams constitute exercises that will be used here and again in Chapter 12. Follow these instructions carefully to save time later: (a) On each sheet of engineering paper reserved for analysis, calculate the vertical shear specific to that member at appropriate intervals across the length of the free-body diagram. Be sure to solve for locations where shear passes through zero. (b) On cach sheet of engineering paper containing the tree-body diagram, neatly draw the related shear diagram directly below the associated free-body diagram. The shear diagram should be located in the middle one-third of the page. Reserve the bottom one-third of the sheet for the bending moment diagram introduced in Chap- ter 12. Be sure to show…
Select a double-angle tension member and design a welded connection to resist a dead load of 12 kips and a live load of 36 kips. The member will be 16 feet long and will be connected to a 5/8-inch-thick gusset plate. Use A36 steel for both the tension member and the gusset plate. Show your results on a sketch, complete with dimensions.
Solve( b) part only in 2 hour plz solve this perfectly this id mecahnical emgeering question so plz don't reject it.