Select a double-angle tension member and design a welded connection to resist a dead load of 12 kips and a live load of 36 kips. The member will be 16 feet long and will be connected to a 5/8-inch-thick gusset plate. Use A36 steel for both the tension member and the gusset plate. Show your results on a sketch, complete with dimensions.

Select a double-angle tension member and design a welded connection to resist a dead load of 12 kips and a live load of 36 kips. The member will be 16 feet long and will be connected to a 5/8-inch-thick gusset plate. Use A36 steel for both the tension member and the gusset plate. Show your results on a sketch, complete with dimensions.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bracket shown is welded by an E70 electrodes fillet weld and is subjected to a factored load Pu=290KN a.) Determine the polar moment of inertia of the group of welds. b.) Determine the max force per mm to be resisted by the weld as shown. c.) Determine the fillet weld size required for the connection. P = 290 kN 175 mm 150 mm Channel Section 500 mm Welding at the back of the channel
Using SMAW process, E70 electrodes and an A572 steel. Determine the length of the side fillet welds for the full capacity the 125x100x10mm angle tension member as shown below. Assume that the member is subjected to repeated stress variations making any connection eccentricity undesirable. Check the block shear strength of the member. Assume that the WT chord has sufficient strength to develop the weld strengths and the thickness of its web is 12mm. Use U=0.87 for class use and LRFD Method only. L125x100x10 V WT BOTTOM CHORD (please solve completely and neatly thank you so much) 12S
Problem 5: The lap connection shown consists of a PL1/2"X3" plate connected to a ½ in gusset plate with ¼" longitudinal fillet welds as indicated. The plates are A36 steel and the electrodes are E70XX. Calculate the length L (in) of the connection to develop the full capacity of the plate. Hint: The full capacity of the plate will depend on the governing strength of the tension member. Neglect block shear. Use ASD 6" x 1/2" P [ T L 1/4 1/4 E70 - 13²x P 3" x 1/2"
If the structural frame is replaced to structural steel and the connections is to be designed, determine the following Determine the centroid of the weld measured from the given origin A. Determine the direct shear load in the welds. Determine the required size of the fillet weld(E60xx) if the maximum resultant load is 750,000 N/mm
10 mm fillet welds Determine the design capacity of the welded lap steel connection shown below. All steel plates are 50X10mm dimension. Both fillet welds are 10mm E48XX SP, continuous across the full plate width. If the connection was tested to failure, which component would fail first.
If the design tensile strength Phi Pn of a tension member is controlled by rupture failure. Which of the following actions will NOT increase its capacity? using welds instead of bolts using larger cross section of the member increasing strength of steel using thicker gusset plate
a welded connection is in eqilibrium under the action of the four forces shown. Knowing that FA=8lbs and FB= 16lbs, determine the magnitudes of other two forces *3dec places all final
See the image. Two steel plates are welded together. The thickness of the bottom plate is 10mm and the thickness of the top plate is 8mm. What is the maximum and minimum sizes of the weld.
Provide a balanced welded connection to mobilize the full capacity of the angle. ( Filler material :fy = 480 MPa, fu = 560 MPa, Members are S235) a Section a-a 10 mm 10 cm P { =37.14 mm 5 cm 16 mm Gusset Plate a
Select a double-angle tension member and design a welded connection to resist a dead load of 12 kips and a live load of 36 kips. The member will be 16 feet long and will be connected to a 5/8-inch-thick gusset plate. Use A36 steel for both the tension member and the gusset plate. Show your results on a sketch, complete with dimensions.
In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to a 16 mm gusset plate for a tensile load of 650 kN. Design the moment free welded connection. The distances of centroid of angle from the back side of legs are C₁=C₁ = 30.9 mm. The strength of the weld per mm thickness per mm length is 76 MPa.
Five M20 8.8/ bolts are used in the connection between a beam and a column. Both sides of the cleat plate are welded to column using fillet weld (Manual metal arc AS4855 B-E43XX) with size of 5 mm. The design force transferred from beam to column is 300 kN. The cleat plate has thickness of 12 mm, fy = 300 MPa, and fü = 360 MPa. Determine the unit stress sustained by the weld