2.) Compute the tensile capacity for the ½ inch thick plate shown. The bolts are 4 inchdiameter high strength bolts. The steel is A36.-Pt1

Answered: Image /qna-images/answer/2a96d598-b8f5-4186-b8b9-e51294008d24.jpg

Answered: 2.) Compute the tensile capacity for…

2.) Compute the tensile capacity for the ½ inch thick plate shown. The bolts are inch diameter high strength bolts. The steel is A36. 21 1 3

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.4.2P

See similar textbooks

Related questions

Q: 1. Determine the allowable load Pa based on bearing at bolt holes. (ASD) 2. Determine the ultimate…

A: Given:- Thickness of plate, t=16 mmDiameter of bolts, d=22 mmNumber of bolts, n=6S1=40 mmS2=80…

Q: Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The…

Q: A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of…

A: A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of bolt…

Q: 3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates of the same…

Q: Determine the tensile strength of the welded A992 WT4×20. WT4 × 20 PL - Transverse weld

A: Given:- The steel section used = WT 4×20 The steel used = A992 To determine:- The tensile strength…

Q: The splicec connected 248 MPa сес CO

Q: TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY…

Q: A steel plate is to be attached to a support with three bolts. The cross-sectional area of the plate…

A: We have to find out the minimum bolt diameter required to develop the full strength of the plate.

Q: A PL 38 x 6 tension member is welded to a gusset plate as shown in figure. The steel is A36. PL % ×…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: bolted lap joint

Q: The given angle bar L125x75x12 with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm…

Q: 4. Calculate the design strength (p.Pn) of W24X76 with length of 12 ft. and pinned ends. A572…

Q: The angle L 8 x 8 x ½ in tension shown in the figure below must resist a service dead load of 35…

Q: Situation 5. The angular section shown below is welded to a 12 mm gusset plate.. Both materials are…

A: The given data is as follows : Size of angular section = 150 x 90 x 12 Area of angular section =…

Q: TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY…

A: Note:- Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt…

Q: PROBLEM NO. 2: Two plates each with thickness t = 16mm are bolted together with 6-22mm diameter…

A: Data Given:S1 = 40 mmS2 = 80 mmS3 = 100 mmt = 16 mmBolt diameter (db)= 16 mmAsked:Allowable strength…

Q: ISA 100 x 100 x 10mm (Cross sectional area = 1908mm2) serves as tensile member. This angle is welded…

Q: Determine the design tensile strength of the plate (200 × 100) mm connected to a 12 mm thick…

A: Given: The dimension of the plate is 200 mm x 100 mm. The thickness of plate is gusset is 12 mm. The…

Q: Complete the table below for the steel sections shown. All sections are bending about their…

Q: An A36 tension member shown in the figure is connected with three 19 mm diamter bolts. Diameter of…

Q: A double-angle shape is shown in the figure. The steel is A36, and the holes are for 2-inch-diameter…

A: Double angle section is shown in the figure above. Grade 60 steel is used. Diameter of bolts= 1/2…

Q: The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The…

A: The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The…

Q: A structural tee bracket is attached to a column flange with six bolts as shown in Figure . All…

A: Solution

Q: Determine the design tensile strength of plate 150 mm x 12 mm size with holes or 16 mm diameter…

Q: 2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the…

Q: Determine the design tensile strength of plate (200 x8 mm) connected to 10-mm thick gusset using 20…

A: Given, Yield stress of the plate fy=250 N/mm2 d=20 mm Diameter of the hole do=20+1=21 mm Ultimate…

Q: An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt…

Q: Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve…

A: 8 number of A325 bolts of dia =22 mm.S1 = 40 mm S3 = 50 mm t1 = 16 mmS2 = 80 mm S4 = 100 mm t2 = 12…

Q: Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle…

Q: Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates…

A: Tensile stress: - When a body is pulled by applying two equal external forces which is normal to…

Q: A single unequal angle 100 x 75 x 6 is connected to a 10 mm thick gusset plate at the ends with six…

A: Given data, For a single unequal angle 100x75 is connected to a 10 mm thick gusset plate at the ends…

Q: tension member is a PL 1⁄2 × 6.

Q: Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap…

A: Given, t = 16mm S1 = 40 mm S2 = 80 mm S3 = 100 mm db = 25 mm Fu = 483 MPa Fy = 345 MPa

Question

2.) Compute the tensile capacity for the ½ inch thick plate shown. The bolts are 4 inch
diameter high strength bolts. The steel is A36.
-Pt
1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.
Determine the tensile strength of the welded A992 WT4×20. WT4× 20 PL – Transverse weld
ISA 100 x 100 x 10mm (Cross sectional area = 1908mm2) serves as tensile member. This angle is welded to a gusset plate along A and B appropriately as shown. Assuming the yield strength of the steel to be 260 N/mm2 the tensile strength of the member can be taken to be approximately A ISA 100x100×10 Gusset Plate B
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
Situation 5. The angular section shown below is welded to a 12 mm gusset plate. Both materials are A36 steel with Fy = 250 MPa. The allowable tensile stress is 0.6Fy. The weld is E80 Electrode and 12 mm thickness. INNOVATIONS Properties of L 150x90x12: y = 50 shear stress of weld = 0.3Fu A = 2750 Allowable REVIEW INNOVATIE a K ➜ www A. 234 KN B. 349 KN b 13. What is the value of P without exceeding the allowable tensile the angle? C. 382 kN p. 413 kN 14. Find required length of the weld based on shear? A. 280 mm C. 300 mm D. 380 mm B. 320 mm 15. Find the required value of a? A. 108 mm B. 97.9 mm D. 185 mm NEW INNOVATIONS REVIEW INNOVATIOf REVIEW NEW INNOVATIONS
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
A PL 38 x 6 tension member is welded to a gusset plate as shown in figure. The steel is A36. PL ½ x 6 The design strength based on yielding is nearest to: The design strength based on rupture is nearest to: The design strength for LRFD is nearest to: The allowable strength based on yielding is nearest to: The allowable strenath based on rupture is nearest to: The allowable strength for ASD.
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear
STEEL STRUCTURES
PROB 2
A36 steel plates are welded as shown. Determine the (a) LFRD design and the (b) ASD allowable strength of the ( c) include block shear strength in the calculations.
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t