2.10 A square yellow it is subjected t the allowable t mum allowable cross section if

Q: C100 x 8 Angle 100 x 75 x 6 The composite shape shown below was manufactured by welding a structural…

A:

Q: Determine the ASD design strength for the A36 plates shown. Use Fy = 248MPA and Fu = 400MPA.

A: Solution: Given data: Fy=248 MPaFu=400 MPa

Q: A spherical section involving the diameter of the sphere. a. Spherical cap b. Spherical cone c.…

A: A spherical section involving the diameter of the sphere is called Spherical Cap.

Q: Determine the reactions for the beam loaded as shown 850KN KN/m *kN/m MATHalino.com mw.onilsHTAM!…

A:

Q: An 5355 Class 1 laterally restrained universal beam (UB) does not support a high shear load. What is…

A: Given data, S355 Class1 laterally restrained universal beam Flange thickness=f=34.3 mm Wez=235x1000…

Q: Determine the moment of inertia of the composite area about the centroidal axis

A: The moment of inertia of the composite area about the centroidal y axis -  IY = IY1 -  IY2 +  IY3 +…

Q: Olim 5x+ 2 4x2-1

A:

Q: Determine the flexural strength for the beam section shown to the nearest integer in kN.m Materials:…

A:

Q: For axially loaded steel column, how could you determine that your section is safe? In case of…

A: In order to determine the safety of the steel column section. The stress available in the section is…

Q: Calculate maximum deflection in a simply supported beam under UDL Support Reactions Internal Bending…

A:

Q: in steel, explain effective length factors

A: Effective length factors (K-factor) are used in the analysis and design of steel structures to…

Q: Find the Y coordinate of the centroid of the composite line shown. ЛУ 2 in 3 in 4 in 2 in 45° 2.65 O…

A:

Q: Determining the spacing of a pair of connecting screws (connectors) between the slab and the steel…

A:

Q: Problem 7.1 - Determine the force in each member of the truss by t method of joints and state…

A: To find force in all members of the truss

Q: A 10 m high 150UC30 steel column is fixed at its base and restrained to move laterally in the x…

A: Given Data: A cross-section data for 150UC30 is given as:…

Q: Determine the centroid C of homogenous strips

A:

Q: -2 m 2 m 2 m 4 m 4 m

A: Locate the centroid of shaded area shown

Q: Determine the moment of inertia of the composite area shown beow about the centroidal y- axis and…

A:

Q: (cos= - sin dx -sin – cos 3m Option 1 O -sin - cos Option 3

A: To find- ddxcosπ2-sin3π4

Q: nle 7.11 Design a composite beam with flexible shear connectors for the following data: Span of the…

A:

Q: How much load must be applied on the wood, with a clear span length of 2350mm, deflection of the…

A: Given:- The clear span length = 2350 mm  The deflection of the wood = 12.5 mm  The modulus of…

Q: A= 63.04 cM², bF = 100 wm, tF = IS-3 wm For ISMC 400 tw = 8.6 mm, Ixx = 15123.4 cm4 For ISA 1asx75X…

A: To determine x bar of the composite section. Centroidal MOI Iyy

Q: applied to the beam cross section. Calculate (a) the tension normal stress in the wood at point K.…

A:

Q: Evaluate: /8(x- 1)xdx (x2.

A:

Q: USE DOUBLE INTEGRATION METHOD TO GET THE MAXIMUM DELECTION OF THE BEAM

A:

Q: QUESTION 2 Determine the value of P just sufficient to start the 60 wedge under the W lb blue block.…

A:

Q: what is the advantages of SAP and stadd in steel design

A: SAP and STAAD are both software tools which are commonly used in structural engineering for both…

Q: 3) For the concrete beams shown, draw the approximate deflection shape and draw the locations of the…

A: To draw: Approximate deflection shape and location of reinforcing bars

Q: Which of the following is the correct classification of beam? unstable stable and determinate…

A:

Q: class Find 22 for Z =*+2 xy and X =U Cosv sy=u sinV.

A: Equation - Z = x2 + 2xy        .....1where,x = uCosvy = uSinv

Q: Mex Force 15 KN APPlied on nail what is The Max V If Spacing between Nail is 75cm ? 15cm 5cm 15cm…

A:

Q: Determine the values of S and Z and shape factor about horizontal x-axis. 14-in 2.5-in 2.5-in 1/2…

A: y = A1y + Ay2 +Ay3 A1 + A2 + A3⇒y = .5×6×3 + 16×.5×6.25 + .5×6×3.5×6 + 16×.5 + .5×6⇒y = 4.8571 in…

Q: True or False? Steel plates that are more than 8-inches in thickness are only available in Fy of 32…

A: To determine: Whether Steel plates that are more than 8-inches in thickness are only available in Fy…

Q: Which of the following statements is NOT correct? O Bolt holes are significant in designing…

A:

Q: H.W: draw the I.L for RA, RC, RF, RD, MD, VCL, VG and MG.

A: Need to draw the ILD(influence line diagram)for

Q: Any one span beam with three hinges not on the same line is called * O Indeterminate beam…

A: The stability of the beam or truss depends on the number of support reactions and the equilibrium…

Q: Locate the center of mass (x̄, y̅, z̅) of the homogeneous block assembly.

A:

Q: An HSS254x152x8.0 section is built into a composite section by welding on two additional flange…

A:

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.