1- A simply supported beam is composed of three plates, which are fastened together using bolts that are spaced at 150mm intervals in the longitudinal direction of the beam. If the allowable shear on the bolts is 15 kN, what is the maximum allowable value of the applied load P? 24 24 Bolts spaced at 150 mm P 70 AB longitudinall - 1.5m 50 5m dimensions in mm 00 24

1- A simply supported beam is composed of three plates, which are fastened together using bolts that are spaced at 150mm intervals in the longitudinal direction of the beam. If the allowable shear on the bolts is 15 kN, what is the maximum allowable value of the applied load P? 24 24 Bolts spaced at 150 mm P 70 AB longitudinall - 1.5m 50 5m dimensions in mm 00 24

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the minimum diameter of the bolt if the maximum shear stress is equal to 10 ksi. The value…

A: dmin = 12/16in final answeri have attached the photo of step by step solutionExplanation:Step 1:…

Q: Bottom chord of truss is composed of two angle bars each having a dimension of 192 mm x 95 mm x 5.4…

A: Bottom Chord of Truss : The horizontal member at lower edge of truss which carries the applicable…

Q: Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross…

Q: 2. Knowing that all joints are glued except along C which is fastened by two bolts at A and B,…

Q: An eccentrically loaded bolted connection is shown. Diameter of A 325 bolts in standard holes is…

Q: Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross…

A: Given, A1 = 1.5 in2 dpin = 0.7 in a = 47 in b = 96 in

Q: Three boards each 50mm thick, are nailed together to form an I-Beam that is subjected to a vertical…

A: Vertical Shear in beam, V = 1200 N Allowable shearing force for each nail, F= 400 N Three boards of…

Q: gid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross…

Q: F7-8. The boards are bolted together to form the built-up beam. If the beam is subjected to a shear…

A: To find out the allowable maximum spacing of bolt .

Q: Determine the development length of the #9 bars. Is it safe?

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 2. The yoke-and-rod connection is subjected to a tensile force of 5 kN. Determine the average shear…

A: The force applied F = 5 kN. The average normal stress in a 40mm diameter rod = 3.98(MPa)The…

Q: SOLVE FOR THE FORCE IN ALL MEMBERS OF THE TRUSS. SHOW SOLUTIONS CLEARLY USING METHOD OF JOINTS AND…

Q: A 5¹8 x 15 DF axial combination 5 glulam is used as the tension member in a large roof truss. A…

Q: Statics

Q: Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm…

A: Member BC: 300mm wide, 10mm plate attached to two 12mm plates at joint C, 3 A490 bolts, A36 plate

Q: bolt circle of radius 125mm. Determine lts if the shearing stress is limited to

Q: Steel design Select an economic double equal-leg-angle section for the tension member BH and GC for…

A: P = 1.2 DL + 1.6 LLDL = 30 kipsLL = 65 kipsTo Find :Design an economic double equal leg angle…

Q: 7) Determine the force in each member of the truss shown below. C F 100 kips 1S' 1S D - 20 ァー 20

Concept explainers

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.

Question

1- A simply supported beam is composed of three plates, which are fastened
together using bolts that are spaced at 150mm intervals in the longitudinal
direction of the beam. If the allowable shear on the bolts is 15 kN, what is the
maximum allowable value of the applied load P?
24 24
Bolts spaced
at 150 mam
P
70
longitudinally -
1.5m
Бо
5m
dimensions in mm
00
24
Beam crovs-section

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross sectional area of 1.40 in.2 and a yield strength of 43 ksi. The pins at B, C, and D each have a diameter of 0.4 in. and an ultimate shear strength of 70 ksi. Each pin connection is a double-shear connection. Specifications call for a minimum factor of safety in member (1) of 1.8 with respect to its yield strength. The minimum factor of safety required for pins B, C, and D is 2.9 with respect to the pin ultimate shear strength. Determine the allowable load P that may be applied to the rigid bar at A. Use overall dimensions of a = 63 in. and b = 129 in.
The truss is suppored by a pin in point A and a roller at point F. Show your FBD
2 kN The beam is made of three boards nailed together to form the double-T cross section shown. If the allowable shear force in each nail is 400 N, determine (a) the absolute maximum shear stress in the wood, B (b) the required spacing s, of the nails between A and B, 2 m 1 m (c) the required spacing sy of the nails between B and C. -150 mm- T25 mm 200 mm 25 mm 25 mm
The force in member EF using the method of section. [Handwritten solution required]
The three-plate moment connection shown below are all shop− welded· to the column and then field bolted to the girder. The beam is a W18 55 that has a factored moment of Mu = 382 kip ft and a factored shear of Vu = 65 kip. All plates are A36 steel (Fy = 36 ksi, Fu = 58 ksi). Plate 2 is connected to the girder using four bolts as shown. All bolts for the connection are 7/8” diameter A325-X. Design Plate 1, including the required number of bolts and dimensions of the plate. Assume an E70XX weld to the column. Consider limit states only for the plate itself. That is, you do not need to consider limit states for the beam or column. For which plate(s) will you need to check the buckling capacity, Plate 1, 2, and/or 3? Explain.
Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross sectional area of 1.25 in.² and a yield strength of 33 ksi. The pins at B, C, and D each have a diameter of 0.5 in. and an ultimate shear strength of 78 ksi. Each pin connection is a double-shear connection. Specifications call for a minimum factor of safety in member (1) of 1.3 with respect to its yield strength. The minimum factor of safety required for pins B, C, and D is 3.1 with respect to the pin ultimate shear strength. Determine the allowable load P that may be applied to the rigid bar at A. Use overall dimensions of a = 64 in. and b = 131 in. (1) b kips P Answer: Pallow= i a B
write legibly
Bottom chord of truss is composed of two angle bars each having a dimension of 185 mm x 146 mm x 8.7 mm. Between them is a gusset plate, 9.5mm thick. At each end of joints, four 19mm-dia. bolts are fastened along the gage line, having an edge distance of 44 mm and 59mm pitch. Use A36 steel Fy 248 MPa Fu = 400 MPa %3D spacing of bolt = 68.9 mm %3D 9 5mm thick gunset plate edge dist Compute the capacity of the bottom chord based on block shear strength, in KN. uad
7. Determine the horizontal shearing stress at 95 mm above the Neutral Axis. 8. Determine the spacing of the bolts.
The figure shows a roof truss and the detail of the connection at joint G. Members BG and CG are angle sections with the thicknesses shown in the The working stresses are 70 MPa for shear in the rivets and 140 MPa for bearing stress due to the rivets. How many 25-mm-diameter rivets are required to fasten the following members to the gusset plate: (a) BG; and (b) CG?
Question 2 Using the Method of Sections find the force in member JK. 15 kips 20 kips 20 kips 10 kips C D Ligh K H A B J 6 bays @ 15'-0" = 90'-0" Upload Choose a File M G N 12'-0"
Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross sectional area of 1.00 in.² and a yield strength of 33 ksi. The pins at B, C, and D each have a diameter of 0.3 in. and an ultimate shear strength of 78 ksi. Each pin connection is a double-shear connection. Specifications call for a minimum factor of safety in member (1) of 1.3 with respect to its yield strength. The minimum factor of safety required for pins B, C, and D is 2.8 with respect to the pin ultimate shear strength. Determine the allowable load P that may be applied to the rigid bar at A. Use overall dimensions of a = 57 in. and b = 117 in. a b B kips P Answer: Pallow= i