The shaft below is fixed at D. A hole with a diameter of 44-mm has been drilled into portion CD of the shaft. If the shaft is made of steel (G= 77 GPa), determine (a) the angle of twist of end A with respect to end D and (b) the maximum shear stress developed in section BC.

The shaft below is fixed at D. A hole with a diameter of 44-mm has been drilled into portion CD of the shaft. If the shaft is made of steel (G= 77 GPa), determine (a) the angle of twist of end A with respect to end D and (b) the maximum shear stress developed in section BC.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The steel tube seen below has an outer diameter do = 60mm and an inner diameter d, = 50mm. It is subjected simultaneously to torque T = 1.5kN-m and to axial load P = 205kN. Determine: (a) the maximum in-plane shear stress and its orientation, (b) the associated normal stress and (c) sketch both on a properly oriented element.
The bell-crank mechanism is in equilibrium for an applied load of P = 48 kN. Assume that a = 290 mm, b = 190 mm, and 0 = 54°. The pin at B has a diameter of d = 10 mm, and the bell crank has a thickness of t = 14 mm. Calculate the average shear stress in the pin at B. Answer: T= i Bell crank a B Support bracket MPa (1) B
The compound shaft is attached to a rigid wall at each end. a = 2 m and b = 1.5 m. For the bronze segment AB, the diameter is 82 mm and G = 35 GPa. For the steel segment BC, the diameter is 62 mm and G = 83 GPa. The maximum shear stress is limited to 50 MPa in the bronze and 60 MPa in the steel. 75 mm 50 mm Bronze Steel a 1. Compute the largest torque kN-m that can be applied considering the maximum shear stress of the bronze segment. a. 8.07 kN-m b. 11.01 kN-m c. 7.26 kN-m d. 8.60 kN-m 1. Compute the largest torque kN-m that can be applied considering the maximum shear stress of the steel segment. e. 5.11 kN-m f. 5.52 kN-m g. 4.67 kN-m h. 4.08 kN-m 1. Compute the largest torque in kN-m that can be applied to the compound shaft. choose from the choices given above.
The bronze shaft is formed by attaching a hollow shaft to a solid shaft. The allowable shear stress of bronze is 100 MPa. Use G = 35 GPa for bronze. a. If the torque applied is 15 kN m, determine the maximum shearing stress developed in the bronze shaft b. Determine the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 100 MPa or an angle of twist of 3.5 in the 3.5-m length.
Problem 1: Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T=2880 N and T;=432 N. The maximum bending moment is atx= 230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). y 230 mm T, 280 mm 30-mm dia. T C 300 mm 250-mm dia. 400-mm dia. 270 N 1800 N a) Sketch a general shaft layout in 2D (x – y axes), including all components and torques, then calculate all reactions. b) Based on the current shaft dimensions and using only forces at B and C, find the lowest critical speed of the shaft. c) Discard the indicated shaft diameter and use DE-Goodman criteria to determine the critical diameter of the shaft based on infinite fatigue life with a design factor n of 1.5. (Take the same value of endurance limit as that used in…
A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 1.9 in. The shaft is subjected to a tensile axial load of P = 17 kips and torques TA = 7 kip-in. and Tg = 28 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element. TB TA ■K Answer: Point H: 0x = Txy = Point K: Txy = A (1) ■H ksi ksi ksi ksi ksi ksi B Ⓡ
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 640 mm, b = 320 mm, h = 400 mm, and 8= 55°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a B KN h
The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load P as shown. a. Determine the torsional shear stress at Point A (50mm from the center) and Point B (on the Surface) b. Determine the absolute maximum torsional shear stress in the shaft. c. sketch the state of stress at point A and draw its corresponding Mohr’s Circle of stress. compute the principal stresses and maximum in-plane stress. T=10.38kN-m
1. A stepped shaft is shown, the region AB is aluminum having G = 28 GPa, and the region BC is steel, having G= 80 GPa. The aluminum portion is of solid circular cross section 45 mm diameter, and the steel region is circular with 60 mm outside diameter and 30 mm inside diameter. A clockwise torsional load of 4000 N-m is applied at B, assume ends A and Care rigidly clamped. De termine the following: a. maximum shearing stress in the aluminum b. maximum she aring stress in the steel (
A solid circular bronze [G = 6,500 ksi] shaft, 6.0 ft long and 1.325 in. in diameter, carries a torque of 90 Ib-ft. For this shaft, determine: (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax = psi (b) Ф%3D
The hollow circular beam is fixed to the wall (with a bracket) on the left and has an end-cap on the right. The cross-section is shown. (a) Determine state of stress at point A & draw the stress element (b) Determine state of stress at point B & draw the stress element A 100 k-in Tout 2 in n=1.75 in В. B 40 k-in C Tout 30 k X