A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 1.9 in. The shaft issubjected to a tensile axial load of P = 17 kips and torques TA = 7 kip-in. and Tg = 28 kip-in., which act in the directions shown.Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.TBTA■KAnswer:Point H:0x =Txy =Point K:Txy =A(1)■HksiksiksiksiksiksiBⓇ

Answered: Image /qna-images/answer/dc3c44bf-0a93-4f41-81f8-ac98827fe7de.jpg

ubjected to a tensile axial load of P= 17 kips and torques T₁=7 kip-in. and Ta=28 kip-in, which act in the directions shown. etermine the normal and shear stresses at (a) point Hand (b) point K. For each point, show the stresses on a stress element. TB TA ■K A (1) H B (2)

ubjected to a tensile axial load of P= 17 kips and torques T₁=7 kip-in. and Ta=28 kip-in, which act in the directions shown. etermine the normal and shear stresses at (a) point Hand (b) point K. For each point, show the stresses on a stress element. TB TA ■K A (1) H B (2)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Eigure 6)…

A: So angle is clockwise and θ=-30°σx=31ksiσy=-38ksiτxy=0

Q: A solid circular bar is fixed at point A. The bar is subjected to transverse load V = 185 N and…

A: Given data:- The given force, V=185 N The given torqueT=2.9 N-m The length L=1.5 m The given…

Q: The rod has a diameter of 40 mm. It is subjected to the force system Fx=1300 N=1300 N, Fy=500 N=500…

A: The diameter of the rod, D = 40mmThe force at the free end, Fx=1300 N, Fy=500 N, Fz=800 N The rod is…

Q: If the output torque on the CD shaft is T ́ = 75 N-m and the motor rotates at 175 rpm, determine the…

A: Given for CD shaft diameter d2=35 mm, radius of gear R2=125 mmand torque T2=75 N-mfor EA shaft…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A: Cross sectional area, Normal stress, To find: The maximum load that suppported by the structure.

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

Q: 300 mm is applied to the bell crank. B -450 mm- (a) Determine the normal stress developed in e 10mm…

Q: 100 mm Q.2) The right figure show the cantilever beam and loading, while the left figure show the…

A: Solution:- 1. Shear stress in the beam:

Q: Q2-) For the given 2D stress state [MPa); (Mega: x 10°, Pa: N/m2) a) Find the normal and shear…

Q: The members of the truss shown have identical cross- 3P sectional area of 200 mm². Determine the…

A: Allowable stress = 40 MPa = 40 N/mm2 Allowable axial displacement = 0.1 mm E = 70 GPa = 70 × 103…

Q: A solid circular bar is fixed at point A. Thebar is subjected to transverse load V = 70 lb andtorque…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross- sectional…

Q: 1) The copper pipe below has an outer diameter of 50 mm, inner diameter of 30 mm, and G = 45 GPa. It…

Concept explainers

Planar Stresses

Question

A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 1.9 in. The shaft is
subjected to a tensile axial load of P = 17 kips and torques TA = 7 kip-in. and Tg = 28 kip-in., which act in the directions shown.
Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
TB
TA
■K
Answer:
Point H:
0x =
Txy =
Point K:
Txy =
A
(1)
■H
ksi
ksi
ksi
ksi
ksi
ksi
B
Ⓡ

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve it fast.
Cylinder of height 2H. radius R. centroid at (0,0.H), axis e3 undergoes deformation x = o(z) = z + 23e3. Assuming stress-strain relation: S = aE, where a is a constant, total force on the base of the cylinder with normal -e3 is f = -1.5anR2 He3 total force on the base of the cylinder with normal - ez is f = 1.5aπR²e3 total force on the base of the cylinder with normal - ez is f = 1.5an R²Hez total force on the base of the cylinder with normal - ez is f = -1.5anR²e3
933. For the state of stress shown in Fig. P-933, determine normal and shearing stresses on the planes whose normals are at +60° sketch of the and +150° with the X axis. Show these stresses on element. Ans. For = 60°, a = 7.32 MPa and = 10 MPa Y 20 MPa T 20 MPa 10 MPa --X 10 MPa
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 69 mm and G = 33.49 GPa. For the steel segment BC, the diameter is 49 mm and G = 83.14 GPa. Given that a = 2 m and b = 1.4 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 63.68 MPa in the bronze and 90.99 MPa in the steel. Round off the final answer to two decimal places.
почин Two horizontal 7.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each connection. 0.5 in. 18 in 18 in P 0.5 in. 45% 18 in. 60 Determine the maximum value of the average normal stress in link AB. The maximum value of the average normal stress in link AB is 60 Two horizontal 7.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each connection. 0.5 in. P 0.5 in. ksi. 18 in. Determine the maximum value of the normal average stress at the midpoint of link BC. The maximum value of the normal average stress at the midpoint of link BC is ksi.
The split ring shown has an inner radius r1 = 0.6 in. and a circular cross section of diameter d = 0.8 in. Knowing that each of the 115-lb forces P is applied at the centroid of the cross section, determine the stress at point A and at point B.
The d = 16-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a = 32 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 90 MPa, and the bearing stress between the rod head and the support plate cannot exceed 145 MPa. Determine the maximum value of Pmax that can be supported by the structure. P Support Plate Rod Answer: Pmax i Hole diameter D Head KN
All forces applied in the system are in the (x - y) plane. The material point B at the top of the beam is rotated at an angle of 15° counterclockwise. It is required that the shear stress is 17.5 MPa for this rotated material point B. At the bottom point A of the beam it is required that the maximum tensile stress is 110 MPa. Determine the load P and the length d that satisfies these constraints defined for points A and B. Given data: L= 4 b, t = b / 25, c = 2b, b = 1000 mm, e = 12, f=5 b/4- q = 2P/L b/ 4 -b/4- P
Problem 2. [Concepts: Internal forces in 2D and average normal stress] The bars of the truss each have a cross-sectional area of 1.25 in². a) Determine the average normal stress in each member due to the loading P = 8 kip. State whether the stress is tensile or compressive. b) If the maximum average normal stress in any bar is not to exceed 20 ksi, determine the maximum magnitude P of the loads that can be applied to the truss. 4 ft 4 ft 4 E 0.75 P 0
The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load P as shown. a. Determine the torsional shear stress at Point A (50mm from the center) and Point B (on the Surface) b. Determine the absolute maximum torsional shear stress in the shaft. c. sketch the state of stress at point A and draw its corresponding Mohr’s Circle of stress. compute the principal stresses and maximum in-plane stress. T=10.38kN-m
Determine the shear stress in pin A (double shear) and the normal stress in DE. The diameter of pin A is 0.125" and the cross section of DE is 0.15"x0.25". -2 ft -2 ft C A E 3 ft 600 lb