Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 11 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 550 mm, b = 275 mm, h = 450 mm, and 0= 60°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 140 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax (1) a = i B b C kN h

Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 11 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 550 mm, b = 275 mm, h = 450 mm, and 0= 60°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 140 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax (1) a = i B b C kN h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 640 mm, b = 320 mm, h = 400 mm, and 8= 55°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a B KN h
The bell-crank mechanism is in equilibrium for an applied load of P= 48 kN. Assume that a = 230 mm, b = 180 mm, and 8 = 65°. The pin at B has a diameter of d = 30 mm, and the bell crank has a thickness of t= 10 mm. Calculate the bearing stress in the bell crank at pin B. (1) P Answer: O= i Bell crank A a C MPa B Support bracket b B F₁
Problem # 4. A 12-mm-diameter steel E 200 GPa] rod (2) is connected to a 30mm wide by 8 mm thick rectangular aluminum [E 70 GPa] bar (1), as shown. required to Determine the force P stretch the assembly 10.0 mm. Ans: = A (1) 0.45 m B (2) 1.30 m - C
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B and bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest hundredths.
15
Part 4a)Determine the reaction (in N) at the hinge at C.b) Determine the diameter of the pin at C in mm.c) Determine the corresponding bearing stress in the pedal at C in MPa.
A truss system is supported by two pins at the top. Determine the absolute value of the axial stress in member AC (in MPa) if the diameter of the member is 30 mm.
The shaft AB is formed by bonding steel tube and a brass core. Outer diameter of the steel tube is 60 mm and the diameter of the brass core is 30 mm. The shaft is subjected to uniform distributed torque o t kNm/m. The allowable shear stresses for steel and brass are (Tsteel)all = 80 MPa and (Tbrass)all = 50 MPa, respectively. Determine a) the maximum value of the uniform torque t , b) the corresponding angle of twist at A. (The shear modulus for steel and brass are Gsteel = 77 GPa and Gbrass = 40 GPa, respectively) - Steel Tube A t kNm/m B 30 mm 15 mm 1 m 1 m Brass Core Cross Section
The bell-crank mechanism is in equilibrium for an applied load of P = 34 kN. Assume that a = 240 mm, b = 140 mm, and 0 = 63°. The pin at B has a diameter of d = 15 mm, and the bell crank has a thickness of t = 6 mm. Calculate the bearing stress in the bell crank at pin B. F₁ Bell crank B a Support bracket Part 1 Use equilibrium to determine the magnitude of the reaction force at pin B. Answer: B = i kN
Radius of the pin at C is 3mm. While at static equilibrium, we know that a force P of magnitude 500 N is applied to the pedal shown, calculate (a) The average shearing stress in the pin at C (b) the corresponding bearing stress in the pedal at C, (c) the corresponding bearing stress in each support bracket at C. 9 mm T 5 mm C A 75 mm 125 mm B 300 mm PI D
The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a = 280mm, b = 170mm, c = 80mm, and θ = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 29 mm. Determine the bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest tenths.
DProb. 2.8-8. Boom AC in Fig. P2.8-8 is supported by a rec- tangular steel bar BD, and it is attached to a bracket at C by