bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 9 mm in diameter. Assume a = 640 mm, b = 320 mm, h = 350 mm, and θ= 50°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 110 MPa, determine the maximum load that can be supported by

Q: In the steel structure shown, a 6-mm-diameter pin is used at C and 10- mm-diameter pins are used at…

A: Determine Vertical Displacement of point A in mm

Q: The pin at C has a diameter xx(see table below). Assume that the pin supports at C is stated at the…

A:

Q: eter of the pin at C in mm.  c. Determine the corresponding bearing stress in the pedal at C in MPa.

A: Take moment about C∑ Mc=0TBA0.125-11000.3=0TBA=2640N∑ Fx=0TBA-Cx=0Cx=2640N∑ Fy=0 Cy=1100N…

Q: A nylon thread is to be subjected to tension of Q (N). The modulus of elasticity, E of the thread is…

A:

Q: Problem 2. Two rods connected at B are restrained at points A and C. The section AB is steel and E,…

A: Given,Es=200GPa Alpha s=12.3×10-6/℃ Eb=100GPa Alpha b=21.5×10-6/℃ ∆T=70℃ Dab=50mm Lab=200mm Dbc=70mm…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

A:

Q: Link AC has a uniform rectangular cross section 3 mm thick and 12 mm wide. Determine the normal…

A: Given: Link AC: thickness= 3mm, Width=12mm

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of P= 15 kN. Assume that a = 300 mm,…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 17 kN applied at A. Assume a…

A: Given data,  F1 = 17 kN a = 300 mm b = 150 mm c = 75 mm Theta = 35° Diameter = 28 mm Bell crank…

Q: 5 kN is distributed equally among the three rivets, fi e bearing stress between a plate and a rivet;…

A: Given data Diameter, d=25mm Load, P=75kN Thickness, t=25mm The expression for area is given as…

Q: The solid aluminum shaft has a diameter of 50 mm and an allowable shear stress of Tallow =60 MPa.…

A:

Q: The rigid beam ABCD is supported by hinge at point c and pinconnected rods at B and D as shown…

A: Given Data -

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings shown.…

A:

Q: Solve

A:

Q: EX. A steel rod 2 m hong has end fram a support structureand fa end a cross- sectional fa3 cm?. The…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 37 kN. Assume that a = 230 mm,…

A:

Q: A force of P₂ = 1000 N is exerted on control arm BC, which is secur assembly are a = 120 mm and b =…

A:

Q: A pin-connected structure is supported as shown in the figure. Bar (1) is made of brass [E = 105…

A:

Q: Bell crank A a C B Support bracket e b B > F₁ it

A:

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

A: Diameter of tie rod, Diameter of pin B, Maximum normal stress, Maximum shear stress, To find: The…

Q: A steel gear, with 80-mm diameter ro d connected to it is used to transmit 600 HP at 200 rpm. The…

A: Given Data  Diameter of rod (D) = 80 mm  Power transmit (P) = 600 HP  Revolution (N) = 200 rpm…

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 39 kN. Assume that a = 290 mm,…

A:

Q: The lap joint is connected by four rivets. Assuming that the axial load P = 30000 lb is distributed…

A: Given  Shear stress of the rivets= 16 Ksi  Bearing stress between rivet and plate = 22 Ksi  Tensile…

Q: -) The 150-mm-diameter rods AB and BC, having the original lengths shown, are joined at the collar B…

A: step 1-

Q: 2. The stepped steel shaft camies the torque T. Determine the maximum allowable magnitude of T if…

A: Finding out maximum torque required in shaft.

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 875 Ib, a = 2.8 ft, b = 2.1 ft, r = 8 in.…

A:

Q: In the following structure, consider the following data: The connection at D is double and has a…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 845 lb, a = 3.0 ft, b = 2.0 ft, r = 9 in.…

A: We have to find the value of magnitude of pin force at A. Given data is W = 845 lb, a = 3.0ft, b 2.0…

Q: Determine the magnitude of the pin force at A. Assume W = 530 Ib, a = 3.6 ft, b = 2.9 ft, r = 9 in.…

A:

Q: 3. The bell crank shown in Figue 3, which is equilibrium under the forces shown in the figure, is…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 38 kN. Assume that a = 260 mm,…

A:

Q: n the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used at B…

A:

Q: www 37 t t ПП B D 800 N/mm 11 2000 N 8.a mm 8.a mm D 8.a mm a) In the system in the figure, since…

A: Yield stress of bar AB = 450 MPaFactor of safety, S = 3

Q: Dron Acompound steel [G=80 GPa) shaft consists of a solid 110-mm-diameter segment (1) and a solid…

A: Given data,  G = 80 GPa Solid shaft 1 diameter = 110 mm Solid shaft 2 diameter = 56 mm Allowable…

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 15 kN. Assume that a = 240 mm,…

A:

Q: A truss system is supported by two pins at the top. Determine the absolute value of the axial stress…

A: Determine the absolute value of the axial stress in member AC

Planar Stresses