Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear stress for the material is T= 300 MPa. Pin A is subjected to doble shear, whereas pin B is subjected to single shear. A 1.5 m B 1.5 m C 30 kN 2.25m

Q: 3

A: Given:- factor of safety =1.6 force=100kips To find:- most economical option

Q: toonges as aasm 12 mm thick plate is conected to two 8 mm thick plates, on either side through a 16…

A:

Q: A threaded steel rod (Es = 210 GPa, dr = 12 mm, as = 12 x 10-6/°C) is held stress free between rigid…

A: Given, Es=210 GPadr=12 mm4αs=12×10-6/°Cdp=15 mτ=45 MPaσ=70MPa

Q: DETERMINE THE AVERAGE PUNCHING SHEAR STRESS THE CIRCULAR SHAFT CREATES IN THE METAL PLATE THROUGH…

A:

Q: *5-4 The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly…

A: Maximum shear stress is 26.73 MpaExplanation:Step 1: Step 2:

Q: The copper pipe has outer and inner diameters of 2.5 in and 2.0 in. If it is tightly secured to the…

A:

Q: P1.020 For the clevis connection shown in the figure, determine the maximum applied load P that can…

A: d = 15 mm  = 75 MPa

Q: For the shaft loaded as shown, which point(s) at the section shown experiences the maximum shear…

A: Let's draw the FBD  for first figure At the L shaft observe the stresses and their directions…

Q: diameter of the smallest pin that can be used if not to exceed a shear stress of 60 MPa (Draw

A:

Q: Problem 2 (for all students). Determine the state of stress, the principal stress and the max in-…

A: Calculating the moment of inertia: IP=π32504-404    The torque will be:T=6×300=1800 KN-mmThe bending…

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: 0-14. A punch of 20 mm diameter is used to punch a hole in 8 mm thick plate. If the force required…

A: Given- Diameter of punch d = 20 mm, Thickness of plate t =8 mm, Force P=110 kN, It is needed to find…

Q: The drill pipe has an outer diameter of 3 in., a wall thickness of 0.25 in., and a weight of 50…

A: For the given drill pipe,

Q: PROBLEM 2 Strips A and B are to be glued together using the two strips C and D. a. Determine the…

A: force transfered by C strip = Force in D strip=force in A strip 2=20 KNlet the width of the strip C…

Q: For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 2…

A: The maximum shear stress in Mpa is =?

Q: Consider the compound system consisting of three sections with cross-sectional areas 3A, 2A, and A…

A: The correct answer to the given questions are as under

Q: ! Required information Each of the four vertical links has an 8 x 36-mm uniform rectangular cross…

A: Given data - Cross section = 8×36 mm Diameter of Pin = 16 mm P = 23 KN Find out - Average shear…

Q: A Single rivet lop joint is to connect 12mm thick plates by providing 20mm dia. rivet at so mm…

A:

Q: Determine the elongation of a 0.5-in, diameter steel bar. Ths elastic modulus of the steel bar is…

A: Given data : Length (L)=10 ftLoad (P)=2000 lbElastic modulus (E)=27000 ksiDiameter (d)=0.5 in

Q: A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate…

A:

Solid Mechanics

Engineering mechanics is a branch of science that deals with forces causing bulk motion in bodies and the effect that these forces cause on the bodies. Engineering mechanics does not deal with the internal changes that occur on account of these external forces. The internal effects in a body or a material under the action of external forces are studied in a new branch of science called solid mechanics, the strength of materials, or the mechanical behavior of engineering materials.