Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 640 mm, b = 320 mm, h = 400 mm, and 0= 55°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. a B b /8 kN

Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 640 mm, b = 320 mm, h = 400 mm, and 0= 55°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. a B b /8 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Torialai Stan Problem 1-- Short link BD consists of a single steel bar 40 mm wide and 12 mm thick. Knowing that = Call 100 Mpa, determine: a) The maximum value of the normal stress in the link BD b) The required pin diameter at support D. 20kN 100 150 mm 300 mm D 30
0.15
The bell-crank mechanism is in equilibrium for an applied load of P = 35 kN. Assume that a = 240 mm, b = 185 mm, and 8 = 65°. The pin at B has a diameter of d = 15 mm, and the bell crank has a thickness of t = 12 mm. Calculate the average shear stress in the pin at B. (1) P Answer: T = i Bell crank a C MPa B Support bracket- b F₁ -- B
#2 handwritten then box the final answers
Determine the magnitude of the pin force at A. Assume W = 520 Ib, a = 2.9 ft, b = 2.4 ft, r = 7 in. a C B A W D Answer: A = i Ib
10. The rigid bar below is supported by axial bar (1) and by a pin connection at C. Axial bar (1) has a cross-sectional area of A₁ = 275 mm², an elastic modulus of E = 200 GPa, and a coefficient of thermal expansion of a = 11.9x 106/°C. The pin at C has a diameter of 30 mm. After load P has been applied and the temperature of the entire assembly has been increased by 31°C, the total strain in bar (1) is measured as 975 μe (elongation). Determine: (a) the magnitude of load P. (b) the shear stress in pin C. 275 mm Connection detail (1) Rigid bar 540 mm 135 mm 260 mm
15
Part 4a)Determine the reaction (in N) at the hinge at C.b) Determine the diameter of the pin at C in mm.c) Determine the corresponding bearing stress in the pedal at C in MPa.
A truss system is supported by two pins at the top. Determine the absolute value of the axial stress in member AC (in MPa) if the diameter of the member is 30 mm.
The shaft AB is formed by bonding steel tube and a brass core. Outer diameter of the steel tube is 60 mm and the diameter of the brass core is 30 mm. The shaft is subjected to uniform distributed torque o t kNm/m. The allowable shear stresses for steel and brass are (Tsteel)all = 80 MPa and (Tbrass)all = 50 MPa, respectively. Determine a) the maximum value of the uniform torque t , b) the corresponding angle of twist at A. (The shear modulus for steel and brass are Gsteel = 77 GPa and Gbrass = 40 GPa, respectively) - Steel Tube A t kNm/m B 30 mm 15 mm 1 m 1 m Brass Core Cross Section
The bell-crank mechanism is in equilibrium for an applied load of P = 34 kN. Assume that a = 240 mm, b = 140 mm, and 0 = 63°. The pin at B has a diameter of d = 15 mm, and the bell crank has a thickness of t = 6 mm. Calculate the bearing stress in the bell crank at pin B. F₁ Bell crank B a Support bracket Part 1 Use equilibrium to determine the magnitude of the reaction force at pin B. Answer: B = i kN
17