The lap joint is connected by 3-20mm diameter rivets. Assuming that the axial load P = 50 kN is distributed equally among the three rivets, find (a) the shear stress on a rivet; (b) the bearing stress between a plate and a rivet and (c) the maximum average tensile stress in each plate. P P 3.1 MPa (b) 33.3 MPa (c) 18.18 MPa 130 mm 25 mm 25 mm P P

The lap joint is connected by 3-20mm diameter rivets. Assuming that the axial load P = 50 kN is distributed equally among the three rivets, find (a) the shear stress on a rivet; (b) the bearing stress between a plate and a rivet and (c) the maximum average tensile stress in each plate. P P 3.1 MPa (b) 33.3 MPa (c) 18.18 MPa 130 mm 25 mm 25 mm P P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

civil engineering. need help.
P1=50kN P2=80kN
8 kN 4 m 15 kN 5 kN 2 m 2 kN 2 m 2 m A B с D E The aluminum rod shown has a diameter of 20 mm and is subject to axial forces acting at A, B, C, and D. Assume the rod has a Young's modulus of E = 70 GPa. a) State the internal axial forces within sections AB, BC, CD, and DE. Remember to indicate whether they are in tension or compression b) What is the displacement of A relative to C? c) What is the displacement of A relative to E?
Assume that 4-18mm diameter rivets join the plates that are each 120mm wide. The allowable stresses are 120MPa for bearing in the plate material and 60MPa for shearing of rivets. Determine the following:a. The minimum thickness of each plateb. The largest average tensile stress in the plate F=70
Part 2,3,4
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm. If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 1. A 200mm 250mm 3. 30 N-m 300mm 20 N-m 80 N m O 2.34MPA O 7.49MPA O 4.68MP O 3.74MPA
Flexure stress *please answer in complete solution and Draw the FBd properly and neatly *
A steel pipe (1) is attached to an aluminum pipe (2) at flange B. Both steel pipe (1) and aluminum pipe (2) are attached to rigid supports at A and C, respectively. Member (1) has a cross-sectional area of A1 = 3,600 mm2 , an elastic modulus of E1 = 200 GPa, and an allowable normal stress of 160 MPa. Member (2) has a cross-sectional area of A2 = 2,000 mm2 , an elastic modulus of E2 =70 GPa, and an allowable normal stress of 120 MPa. Determine the maximum load P that can be applied to flange B without exceeding either allowable stress.
. Problem 4: The lap joint is connected by 3 20mm - diameter rivets. Assuming that theload P = 50 KN is equally distributed among the 3 rivets, find-The shear stress in each rivet. - The bearing stress between rivet and plate. - The tensile stress in each plate.
Torialai Stan Problem 1-- Short link BD consists of a single steel bar 40 mm wide and 12 mm thick. Knowing that = Call 100 Mpa, determine: a) The maximum value of the normal stress in the link BD b) The required pin diameter at support D. 20kN 100 150 mm 300 mm D 30
Point B & C. Please complete solution and no rounding off.
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Мра. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm F F mm. 50 mm 340 mm