The rigid bar ABC shown in Fig. is hinged at A and supported by a steel rod at B. Determine the largest load P that can be applied at C, if the stress rod is limited to 207MPa and the vertical movement of end C must not exceed 0.25mm. Ans: P= 2.111KN 0.6m B Steel L= 1.22 m A= 322 x 106 m² E= 200 GPa 0.9m P

The rigid bar ABC shown in Fig. is hinged at A and supported by a steel rod at B. Determine the largest load P that can be applied at C, if the stress rod is limited to 207MPa and the vertical movement of end C must not exceed 0.25mm. Ans: P= 2.111KN 0.6m B Steel L= 1.22 m A= 322 x 106 m² E= 200 GPa 0.9m P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A composite bar as shown in Fig 3 is firmly attached to unyielding supports at the ends and is…

Q: An axial load P is supported by the short steel column shown in the figure. The column has a…

A: Given that, Axial load = P Cross-sectional area of column = Acolumn=13,300 mm2 Allowable average…

Q: Using this equation FL/AE Q1/The rigid bar BDE is supported by two rods AB and CD. Rod AB is made of…

Q: Observe the figure that shows the assembly of the ACD arm, suspended by a bearing in C coupled to a…

Q: A diagonal aluminum alloy tension rod of diameter d and initial length / is used in a rectangular…

A: We have to determine Deformation of aluminum rod

Q: The rigid beam shown is supported by a pin at A and two steel rods each of diameter 16 mm. If P = 30…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3100 mm² and an…

A: According to the given dataThe area of bar 1 is .The allowable normal stress in bar 1 is .The area…

Q: H.W: 1 rod as shown in Fig. P-108. Axial loads are applied at the positions indicated. Find the…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ - 3800 mm² and an…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 2850 mm2 and an…

Q: A horizontal load PP is applied to an assembly consisting of two inclined bars, as shown in the…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 8) Determine load P that…

Q: Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A 3650 mm2 and an…

A: Stress is a physical mass that expresses the inner forces of a continuous material exerted upon each…

Q: A tapered bar AB of solid rectangular cross-section with a thickness of 20 mm and length L = 800 mm…

A: To Find : The elongation of the bar due to load P . Given : The thickness is t=20 mm The length…

Q: PROBLEM 1 A threaded steel rod (E=210 GPa, d: = 15mm, linear coefficient of expansion= 12x10-6/0C)…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3200 mm² and an…

A: To Find : The maximum load Pmax. Given : The cross section area of bar 1 is A1=3200 mm2 The cross…

Q: THe bracket shown is made of cold drawn steel with Sy=400MPa and Su=480 MPa, and is fastened to a…

Q: The figure below shows the cross section of a steel rectangular tube, of uniform thickness t= 25 mm,…

Q: torsion as shown. Determine the Perimeter of then

A: we know that , shear stress =T2t Am A0 =T2tζ Am = A0T = Torque t = thickness to obtain area we…

Q: B 0.75 m 1.5 m 2 m A = 300 mm? A = 250 mm2 A = 5 mm D E = 200 GPa

A: Given,

Q: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm- diameter…

A: Write the given data. Diameter, dB=dD=dF=15 mm=0.015 mElastic modulus, E=200 GPaa=2.671 mb=1.834…

Q: A horizontal load Pis applied to an assembly consisting of two inclined bars, as shown in the…

Q: 3 a M The scheme of supporting of the absolutely rigid body is shown in the picture. The minimal…

A: Given data: The value of a is a = 1.6 m. The magnitude of the moment is M = 8 kN-m. The admissible…

Q: A plate is connected to another plate via 20 mm diameter rivets. It carries a load of P=155 kN at a…

Q: An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the…

Q: The rigid bars shown are separated by a roller at Cand pinned at A and D. A steel rod at B helps…

Q: Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A1 = 2350 mm2 and an…

Q: Q3/ The rigid bar ABC shown in Fig. P-212 is hinged at A and supported by a steel rod at B.…

Q: A gazebo is planned to be constructed in a community park as an additional shelter for visitors from…

A: Solution: Given Data: A=7200 mm2SR=0.026E=200 GPaσy=233 MPaFOS=1.67K=0.7 (for Fixed-pinned end)

Q: Answer: Pmax= i kN

Q: As shown in the figure below, determine the internal loadings at points A,B and. Consider the…

Q: An axial load Pis supported by the short steel column shown in the figure. The column has a…

A: Cross sectional area of the column, Acolumn= 16200 mm2 Average normal stress in the steel column,…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3950 mm² and an…

Q: C. For the figure shown below, if the stress in steel and bronze are not exceeding 150MPA and 70MPA…

Q: 4. A steel bar of 40 mm × 40 mm square cross-section is subjected to an axial compressive load of…

A: Given data , Bar of square shape having area - 40*40 mm2 So Area A = 1600mm2 Where comprehensive…

Q: Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of…

A: σBD=200 MPaLbd=48 mmhbd= .95 ma Now link BD σBD=P1AP1=200×π4×482P1=361.911 KNNow taking moment…

Q: Question 3 of 12 View Policies D Answer: Pmax= Current Attempt in Progress A pin-connected truss is…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The rigid bar ABC shown in Fig. is hinged at A
and supported by a steel rod at B. Determine
the largest load P that can be applied at C, if the
stress rod is limited to 207MPa and the vertical
movement of end C must not exceed 0.25mm.
Ans: P= 2.111KN
0.6m
Steel
L= 1.22 m
A= 322 x 106 m²
E= 200 GPa
0.9m
P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel rod is stretched between two rigid walls and carries a tensile load of 5000 N at 20°C. If the allowable stress is not to exceed 130 MN/m² at -20 °C, what is the minimum diameter of the rod? Assume k = 11.7 µm/(m-°C); E = 200 Gpa A. 10.22 mm B. 11.22 mm C. 12.22 mm D. 13.22 mm Please solve the Problem elaborately and Refer Machine Elements and Stresses Equations from the figures or use other shortcut Methods you have or you may Solve both or in more different methods the better ?. Your solution will be use as reference for my Future Board Exam preparation/review/study. Thank you so much dear your work will be appreciated much and rated excellently.
a vertical hollow circular shaft of aluminum shown below fixed at the top has a load P equal to 150KN exerted on its lower end. neglecting self weight, determine the minimum outer diameter d2 and maximum inner diameter d1 if a) the allowable stress = 50MPa b)the allowable elongation =2mm the thickness of the material is one tenth of the outer diameter and young modulus E = 80000MPA
Stress in the left rod after its lowered attached to the support, use FBD
Introduction to Fem
A rectangular steel plate with a thickness h of 5 mm is shown below. All four edges are fixed. An uniform pressure of 20 MPa is applied on the top face of the plate. (Use E=210GPa and v=0.3) 1200 mm Please determine: 1) the maximum stress in the plate; and 2) the maximum deflection in the plate. 600 mm
answer d and e
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4250 mm2 and an allowable normal stress of 95 MPa. Bar (2) has a cross-sectional area of A2 = 2750 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 2.1 m, x2 = 3.6 m, y1 = 0.8 m, and y2 = 2.8 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
For 10 to 12. The compound bar ABCD has a uniform cross-sectional area of 0.25 in². When the axial force P is applied, the length of the bar is reduced by 0.018 in. The moduli of elasticity are 29 x 106 psi for steel and 10 x 10 psi for aluminum. 18 in. 6 in. 18 in. P. P Steel B C Steel D -Aluminum 10. What is p? 11. What is the total elongation of the two steel sections? 12. What is the elongation of the aluminum section?
Rigid member AB is supported by hinge support at A and a 12-mm-diameter wire BC at B as shown. The diameter of the pin at A is 10 mm, thickness of member AB is 20 mm, and the thickness of each bracket of support A is 15 mm. Use a factor of safety FS= 2 and following failure stresses to determine the maximum load w (kN/m) the member can support. For wire BC: G=350 MPa Pin at A: Ta=200 MPa Support brackets: (Gharn n=150 MPa d-12 -35m 3m 20 mm smm Member AB- 10 mm Support Bracket- Support Bracket Conection detail at EpetA
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 3950 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 2900 mm2 and an allowable normal stress of 160 MPa. Assume x1 = 2.0 m, x2 = 3.0 m, y1 = 0.8 m, and y2 = 2.8 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
A steel bar 40 mm x 40 mm square cross-section is subjected to an axial compressive load of 200 kN. If the length of the bar is 2 m and E= 200 GPa, the elongation of the bar will be (a) 1.25 mm (b) 2.70 mm (c) 4.05 mm (d) 5.40 mm e) none of these