Q3/ The rigid bar ABC shown in Fig. P-212 is hinged at A and supported by a steel rod at B. Determine the largest load P that can be applied at C if the stress in the steel rod is limited to 30 ksi and the vertical movement of end C must not exceed 0.10 in. Figure P-212 Steel L= 4 ft A- 0.50 in E- 29 x 10° psi 3 ft

Q3/ The rigid bar ABC shown in Fig. P-212 is hinged at A and supported by a steel rod at B. Determine the largest load P that can be applied at C if the stress in the steel rod is limited to 30 ksi and the vertical movement of end C must not exceed 0.10 in. Figure P-212 Steel L= 4 ft A- 0.50 in E- 29 x 10° psi 3 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem #3 Three rods, each of area 200 mm², jointly support a 7.5 kN load, as shown in the figure. Assuming that there was no slack or stress in the rods before the load was applied, find the stress in each rod. Use Est = 200 GPa and Ebr = 83 GPa. Sted 7.5 KN 2.75 m
A horizontal load P is applied to an assembly consisting of two inclined bars, as shown in the figure. The cross-sectional area of bar (1) is 1.30 in.2, and the cross-sectional area of bar (2) is 1.75 in.2. The normal stress in either bar may not exceed 24 ksi. Determine the maximum load P that may be applied to this assembly. Assume dimensions of a=14.5 ft, b=9.0 ft, and c=14.5 ft. Determine the allowable force F1 in member (1) and the allowable force F2 in member (2).
Problem 3. As shown in the Figure below, please determine the internal force in the middle of AB, with the given data: OA-15 cm, OB-30 cm, OC-60 cm. W=40N, Wo=60N. F=1214N, B-10°, FM=1236 N, and 8=15%. Fj B FM W Wo 4
Based on the figure below, a pin supports a bar at Z and a cable supports X to Y around W. Determine the stress in the cable in megapascal with a diameter of 0.68 inch and a weight of 1,550 pounds. a = = 1 ft b= 3 ft c = 10 ft X bft Y W aft cft Z
A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown in fig. the bar carries a load of 20 KN at B. the cross section areas of steel and copper are 200 mm2 and 400 mm2 respectively find the stress in each ?rod if Es=210 GPa and Ec=83 GPa Copper rod- 2 m Steel rod. -1 m- 1 m 2m -1 m- B 20 KN
The two wooden boards shown in Figure are connected by a 0.5-in.-diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D = 2 in. and d = 5/8 in. The nut is tightened to cause a tensile stress of 9,000 psi in the bolt. Determine the bearing stress between the washer and the wood. Bolt Washer ANSWER: D psi Washer Nut
PROBLEM 2. The carrier system in the figure consists of the AB rigid beam and two aluminum bars and a steel bar connected to it. After the assembly is created at 20 °C without causing any prestresses, calculate the stresses on the bars if the temperature is increased to 80 C. Steel A-36 A =160 mm? 3,5m 10 kN/m 3 m 3m 2 m 2014-T6 Aluminum A =200 mm E A,
Question #4 Bar (1) in the figure has a cross-sectional area of 0.75 in². If the normal stress in bar (1) must be limited to 30 ksi, determine the maximum load P (in kips) that may be supported by the system. The connections at A, B and C are pins. A 6 ft D B (1) 4 ft