A horizontal load Pis applied to an assembly consisting of two inclined bars, as shown in the figure. The cross-sectional area of bar (1) is 1.55 in.?, and the cross-sectional area of bar (2) is 1.75 in.?. The normal stress in either bar may not exceed 23 ksi. Determine the maximum load P that may be applied to this assembly. Assume dimensions of a = 17.0 ft, b = 6.5 ft, and c = 11.5 ft. (1) a B P (2)

A horizontal load Pis applied to an assembly consisting of two inclined bars, as shown in the figure. The cross-sectional area of bar (1) is 1.55 in.?, and the cross-sectional area of bar (2) is 1.75 in.?. The normal stress in either bar may not exceed 23 ksi. Determine the maximum load P that may be applied to this assembly. Assume dimensions of a = 17.0 ft, b = 6.5 ft, and c = 11.5 ft. (1) a B P (2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. The diameter of aluminum rod (1) is 2.50 in., the diameter of brass rod (2) is 1.75 in., and the diameter of steel rod (3) is 3.00 in. Determine the axial normal stress in each of the three rods. Assume P = 5 kips, Q = 3 kips, R = 13 kips and 5 = 24 kips. The normal stress is positive if tensile and negative if compressive. σ₁ = Answers: 0₂ = (1) 03 = (2) i i A Q B C D ksi ksi ksi
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 4 kips, R = 18 kips and S = 21 kips. Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.Answer: F1 = ? kips.
Solve by hand please and correct answer
Determine the largest weight W (in Ib) that can be supported safely by the structure shown in the figure. The working stresses are 17800 psi for the steel cable AB and 696 psi for the wood strut BC. Neglect the weight of the structure. Round off the final answer to two decimal places. 0003.png ... |A 9 ft A = 0.5 in.2 12 ft A/ A = 16 in.2
A pair of 1500 N.m magnitude is applied to the crank of an engine shown in the figure. Shown at position (a) the force P required for it (b) occurs in the uniform section BC arm of 40 mm2. determine the future average normal stress
Handwritten solution
@2 The support consists of solid brass post surrounded by a steel tube. Before the load is applied, the gap between these two parts is | mm. Given the dimensions shown in the figure, determine the greatest axial load that can be applied 0 the rigid cap A if the maximum allowable stress in brass is (Guiin)se = 150 MPa and the maximum allowable stress in steel is (Gun ) = 200 MPa. E, = 200 GPa and Ey,= 100GPa.
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 920 mm2. Assume a = 2.4 m, b = 9.0 m, and c = 4.1 m. If P = 60 kN and Q = 75 kN, determine the normal stress in each member. P y L₂ C MPa (C) Answers: OAB = a b
i need the answer quickly