A pair of 1500 N.m magnitude is applied to the crank of an engine shown in the figure. Shown at position (a) the force P required for it (b) occurs in the uniform section BC arm of 40 mm2. determine the future average normal stress

Q: Q2) For the problem shown in the figure, - Find the axial displacement at the end B - Determine the…

A: for solution refer below images.

Q: Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm…

A: stress is defined as the force per unit area.

Q: 5 kN.m is applied to the purlin in a plane at an angle of 30 deg to the vertical y axis. If the…

A: givenM=5000Nm, θ=30οMx=5000×103 cos30ο=4.4×105 N-mmMy=5000×103sin 30ο=2.2×105 N-mm

Q: A 150 min x a mnm x 20 mm stecl plate is subjected a pull of 150 kN along its central axis as show…

A:

Q: The collar bearing shown is subject to a 500 kN force. 500 kN The collar is 25 mm thick. Find d and…

A: Given data: The axial force on collar bearing is F = 500 N. The collar thickness is t = 25 mm. The…

Q: A force of 120 lb is applied to the edge of the member shown in the figure below. Neglect the weight…

A: given: P=120 lb Solution: Maximum bending moment is given as : Mmax=P×4.5=120×4.5=540 lb-in

Q: A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5…

A: Given data: p=5 MPar=500 mmt=10 mm Need to determine the average circumferential (hoop) stress.

Q: P Tav P σαν

A: GivenA=0.024 mθ=40oσav=200kPaP=8.18 kNτav=-168 kPa

Q: A rigid plate (AC) is connected to flat steel bars by pins at A and B. The horizontal flat steel bar…

A: A rigid plate (AC) is connected to flat steel bars by pins at A and B. The horizontal flat steel bar…

Q: PROBLEM 2. The forces shown in the figure are applied to a plate connected to a pipe with an outer…

A:

Q: 1. Find the flexural stress at point A 2.5 kN/m 2.25 m 3.5 m

A:

Q: 4.3 The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the…

A:

Q: 3. The composite bar consists of a 20-mm diameter steel segment AB and 50-mm diameter brass end…

A: Given Data The diameter of the AD section is: d1=50 mm The diameter of the AB section is: d2=20 mm…

Q: Q.3. A circular bar of 500mm length has across section as shown in the figure. Determine max. axial…

A: As per the standard values of E, it's unit must be in N/mm2 but it is given as N/m2. I have…

Q: 1. In the figure shown, determine the stress in the cable C if its area is 600 mm². Neglect the…

A:

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this…

A:

Q: 2. From the system shown in the figure, obtain the forces and the average axial stress on each bar…

A:

Q: Member AC is shown in Figure is subjected to a vertical force of 3 kN.Determine the position x of…

A: The free-body diagram of the member AC has three forces. Now write moment equation about point 'A'…

Q: rod of length L having uniform cross-sectional area A is subjected to a tensile force P . If the…

A: Given: A rod of length L having uniform cross-sectional area A  is subjected to a tensile force P…

Q: The lap joint is connected by three 20-mm-diameter rivets. Assuming that the axial load P=50 kN is…

A: Welding joints are used to join two different materials together. There are different types of…

Q: A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5…

A: Given Data⇒ Internal Pressure(P)=5 MPa Inner radius(R)=500 mm Thickness(t)= 10 mm

Q: Bronze Aluminum Steel A=400 mm2 A=600 mm A=300 mm2 2P ЗР 4P 3m 5m- -4m-

A:

Q: P. Find the maximum allowable value of P (in lbs) if the working stresses are 40 ksi for steel and…

A:

Q: Solve for the force in BD, vertical reaction at point C, horizontal reaction at point C, resultant…

A: Note:-  As per honor code and answering guidelines I can answer first three sub parts at a time.If…

Q: The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are…

A:

Q: (8) The homogeneous bar is supported by a smooth pin at C a cable that runs from A to B around the…

A:

Q: The mechanism below consists of a solid shaft with a diameter of 2 in between A and B and a hollow…

A:

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this…

A:

Q: P to point A of the section given in the figure Plot the normal stress distribution in the section,…

A: Given dataP=20kN Here are calculation the Moment of inertia about the neutral axis

Q: The uniform 300-1b bar AB carries a 500-lb vertical force at A. The bar is supported by a pin at B…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.