The rod shown below is of diamater 70 mm and is fixed at one end. It is subjected to 500 N.m and 300 N.m torsional moments as shown. Sketch the distribution of the internal torsional moment along the length of the rod. Also find the torsional shear stress at points A and B, and also the largest shear stress in the rod. Point B is to the left of the 500 N.m torsional moment and A is on the right of it. Round-up your answers to the nearest 1/100th of an MPa. 35 mm 20 mm 500 N.m 35 mm- 300 N.m Torsional shear stress at A = MPa Torsional shear stress at B = MPa Maximum shear stress = MPa

The rod shown below is of diamater 70 mm and is fixed at one end. It is subjected to 500 N.m and 300 N.m torsional moments as shown. Sketch the distribution of the internal torsional moment along the length of the rod. Also find the torsional shear stress at points A and B, and also the largest shear stress in the rod. Point B is to the left of the 500 N.m torsional moment and A is on the right of it. Round-up your answers to the nearest 1/100th of an MPa. 35 mm 20 mm 500 N.m 35 mm- 300 N.m Torsional shear stress at A = MPa Torsional shear stress at B = MPa Maximum shear stress = MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The built-up shaft in figure consists of a pipe AB and a solid rod BC. The pipe has an inner diameter of 20 mm and outer diameter of 28 mm. The rod has a diameter of 12 mm. Determine the average normal stress at points D and E A 4 kN D B 6 kN 6 kN E -8 kN
The copper pipe (G= 50 GPa) is tightly secured to the wall at A, has an outer diameter of 40 mm and an inner diameter of 37 mm, and subjected to three torques as shown in Figure 5. Determine the absolute maximum shear stress developed in the pipe and plot the variation of shear stress through the pipe wall. (i) (ii) Produce a graphical plot of the variation of angle of twist from end A to the free end (wind-up diagram) if the distances between the applied torques is equal at 300 mm. 80 N.m 20 N·m Figure 5 30 N.m
The rigid wrench (not the brand Rigid sold at Home Depot!) shown is used to loosen a stuck nut at the top of a 4 mm radius smooth shafted bolt that is fixed supported at the base A. Determine the largest force F that can be applied if the bolt has a maximum shear stress of for this maximum torque value. G=75 GPa 18 MPa. Also determine the distance each force will move Ans: 6.03 N F. 150 mm 150 mm 80 mm
A shaft used in an aircraft engine is 50 mm diameter, the maximum allowable shear stress is 84 MN/m². Find the torsional strength of the shaft. If the shaft now has a hole bored in it, find the percentage reductions in strength and mass. a. If the hole is 40 mm diameter b. If the hole is 25 mm diameter.
The bell-crank mechanism shown in the figure is in equilibrium. Determine (1) the normal stress in the connecting rod CD; (2) the shearing stress in the 8- mm-diameter pin at B point; (3) the bearing stress in the bracket supports at B; and (4) the bearing stress in the crank at B point. D 5 KN 70° A 200 mm 10 mm- BO 150 mm 8 mm 6 mm P
Solve clearly and neatly
The horizontal bar ABC is supported by a pin at A and two rods with identical cross-sectional areas. The rod at B is steel and rod at C is aluminum. Use P = 45 kN, E for steel = 200 Gpa and aluminum = 70 Gpa, m = 1.00 m, n = 0.50 m Steel Aluminum A m m – P. A. Determine the deformation (in mm) of the steel rod B. Determine the deformation (in mm) of the aluminum rod C. Determine the vertical movement (in mm) of force P 4 decimal places
When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this pin so that the resulting shear stress on the pin at C is 40 MPa.
The hollow ACB shaft made of steel has an inner diameter of 40 mm and an outer diameter of 50 mm and is fixed against rotation at the A and B ends. As shown in the figure of a rod welded vertically to the shaft at point C of the shaft, P forces are applied to the ends in the horizontal direction. If the maximum allowable slip on the ACB shaft is 45 MPa, determine the largest value of the P force. stretching
ضههقحشمبترذ
The compound bar has an assembly shown. AB is steel (Es = 200 GPa, αs = 11.7 x 10-6 / oC) BC is brass (Eb = 105 GPa, αb = 20.9 x 10-6 / oC) Supports are fixed and unyielding. The rods are initially stressed free. Determine the stress (MPa) in brass for a temperature rise of 100 oC. Neglect the weight of the materials.
HWK 4-2.2-3: Find the shear stress about the neutral axis if V = 2000k