The horizontal bar ABC is supported by a pin at A and two rods with identical cross-sectional areas. Therod at B is steel and rod at C is aluminum.Use P = 45 kN, E for steel = 200 Gpa and aluminum = 70 Gpa, m = 1.00 m, n = 0.50 mSteelAluminumAm m –P.A. Determine the deformation (in mm) of the steel rodB. Determine the deformation (in mm) of the aluminum rodC. Determine the vertical movement (in mm) of force P4 decimal places

(a) To find: The deformation of the steel rod. Given: The Young's modulus of steel is Es=200 GPa.…

The horizontal bar ABC is supported by a pin at A and two rods with identical cross-sectional areas. The rod at B is steel and rod at C is aluminum. Use P = 45 kN, E for steel = 200 Gpa and aluminum = 70 Gpa, m = 1.00 m, n = 0.50 m Steel Aluminum A B C mm →→ n P A. Determine the deformation (in mm) of the steel rod B. Determine the deformation (in mm) of the aluminum rod C. Determine the vertical movement (in mm) of force P K

The horizontal bar ABC is supported by a pin at A and two rods with identical cross-sectional areas. The rod at B is steel and rod at C is aluminum. Use P = 45 kN, E for steel = 200 Gpa and aluminum = 70 Gpa, m = 1.00 m, n = 0.50 m Steel Aluminum A B C mm →→ n P A. Determine the deformation (in mm) of the steel rod B. Determine the deformation (in mm) of the aluminum rod C. Determine the vertical movement (in mm) of force P K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A prismatic steel bar of square cross section 3 in. x 3 in. is subjected to a tensile load P = 135…

A: Solution: Given Data: P=135 kipsAn=6 in2θ=45o

Q: Determine the downward displacement δ of the lower end of the copper bar with respect to the base…

A: Find deflection of lower point of copper and maximum force

Q: The drill shown is jammed in the wall and is subjected to the torque and force shown in the diagram.…

A: Given

Q: Force on the Bronze Material Force on the Aluminum Material Force on the Steel Material Maximum…

A: To find. Force on the Bronze Material Force on the Aluminum Material Force on the Steel Material…

Q: e state of stress at a point in a circular bar under pure torsion is given by T xy = T yx= t and…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: According to the given dataBarNormal-StressDiameterThickness1175MPa10mmNA216548mm6Considering the…

Q: A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper…

Q: 2. Two elastic bars are connected and supported as shown. The thermal load is a 10°C temperature…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

The horizontal bar ABC is supported by a pin at A and two rods with identical cross-sectional areas. The
rod at B is steel and rod at C is aluminum.
Use P = 45 kN, E for steel = 200 Gpa and aluminum = 70 Gpa, m = 1.00 m, n = 0.50 m
Steel
Aluminum
A
m m –
P.
A. Determine the deformation (in mm) of the steel rod
B. Determine the deformation (in mm) of the aluminum rod
C. Determine the vertical movement (in mm) of force P
4 decimal places

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel shaft with a length of 3.00 m. One meter of the steel is contained in a brass tube and firmly attached. The diameter d1 = 70 mm and the diameter d2 = 90 mm. Brass G = 39GPa and steel G = 77.20 GPa. Determine: The torque that can be applied if the deformation at one end is 10 degrees. Answer: T = 8.64 kN – m The torque that can be applied if the maximum shear stress in brass is 70MPa and in steel is 110MPa. Answer: T = 6.352 kN – m Recommendation: analyze by segments. The first segment is only brass, then the composite part between brass and steel, and the last part only steel. In the composite segment, use only one material. In this same segment, equalize the deformations.
3. A steel rod of 3 cm diameter and 5 m length is connected to two grips and the rod is held at a temperature of 95 °C. Determine the stress in the rod, and the force in the rod if the temperature drops to 30 °C for the following cases a. The grip ends do not yield b. The grip ends yield by 0.12 cm Assume the Young's Modulus of the rod is E = 2×105 MPa, and the CTE is a=12×106/ °C
Calculate non-zero stress components (normal and shear) at points A, B and C. Point C is located at the center of the cross section attached to the wall. Calculate non-zero strain components at point B. Neglect shear stress due to shear force. Given: loading F = 400 N, P-2000 N, and T = 75 N·m, Young's modulus E = 70 GPa, Poisson's ratio v = 0.25 15-mm D. -100 mm
4. The stepped circular bar shown below is made from aluminum (E = 70 GPa, v = 0.35). Each segment is 400 mm in length. Prior to applying the loads, the bar has the dimensions shown. The structure is axially loaded as shown. Determine the stress in each segment, the maximum stress and its location, the final in length of the structure, and the final diameters of each segment due to the applied loads. All dimensions shown are in mm. Ø 25 40 15 ↑ Fu 300 kN 600 kN 300 kN
A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine the normal stress σn perpendicular to plane AB and the shear stress τn⁢t parallel to plane AB. Assume α= 30°.Calculate the normal force N perpendicular to the plane AB and the shear force V parallel to plane AB. Report both answers as positive numbers.Answers: N = kips, V = kips.
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section
Problem 7 The shear stress-strain diagram for an alloy is shown in the figure. If a bolt having a diameter of 0.25 in. is made of this material and used in the lap joint, determine the modulus of elasticity E and the force P required to cause the material to yield. Take v=0.3. 7 (ksi) Ty= 50 0.004 y (rad)
Please show the formula used and free body diagram A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
A steel torsion bar AB with diameter d = 34 mm, and ductile material of tensile yield strength Sy = 276 MPa is attached to a rigid arm at A, supported by a bearing at C, and fixed at B, as the picture shows. At the right end of the arm is mounted the wheel on which the vertical force P acts from the ground and which passes through the center of the wheel. If bearing C acts as a simple support and the effect of transverse shear due to P is negligible, determine the maximum force P (in kN) that can be applied to the wheel. Consider a factor of safety n = 2.5. Use the maximum energy of distortion failure criterion and do the analysis on bar AB (torsion bar) in the section where the bearing is.
1