For the two-bar planar truss shown in Figure Q1 below, determine the displacements of node 1 and the stress in elements 1-3. 2 E = 200 000 MPa A = 300 mm² -500 mm- for both members 300 mm Figure Q1 20 kN 1 400 mm 3

Q: Suppose that P₁ = 600 lb and P₂ = 800 lb. Suggestion: Use the sections shown in (Figure 1). Figure 6…

A:

Q: A plane truss has a pin support at A and a roller support at E(see figure).(a) Find reactions at all…

A: The free-body diagram of the provided truss is drawn below.

Q: The three-member frame has original dimensions as shown in the figure. Elements F-D-B and A-B-E are…

A: givenElement FDB and ABE are rigid. so axial and flexure deeflection is zero.Area of CD…

Q: Three solid cylindrical rods are welded together to form the compound axial member shown in the…

A: This question is related to solid mechanics. deformation is defined as the extension or compression…

Q: Cable DB supports canopy beam OABCas shown in the figure. Find the required cross-sectionalarea of…

A: Draw a diagram for the problem. Here, T is the tension in the cable, θ is the angle made by the…

Q: A steel cantilever beam is made of two T-shaped structures welded to each other as shown in the…

A: Given data as per question Allowable stress in tension =150 Mpa Allowable stress in compression =…

Q: Determine the internal forces at point J for the structure shown, where member BD can only carry…

A:

Q: Find the force in member HI

A:

Q: Find the residual forces acting in a truss with members AC=1000N (T), EG=520N (T), and FH= 1200N (C)…

A: to find value of load and member forces

Q: Problem 4-21: The rigid beam is supported at its ends by two A- 36 steel tie rods. If the allowable…

A: Given:The allowable stress of the steel, The load, The value of The length of the rods,

Q: The cross-sectional area of each member of the truss shown in the figure. Calculate the stress in…

A:

Q: If the maximum stress both in tension and compression is not to exceed 120 Mpa, determine the…

A: Step 1: Step 2: Step 3: Step 4:

Q: A train is parked on a steel bridge as shown in the figure below. The steel bridge is simply…

A:

Q: For the truss shown below, use symmetry to determine the displacement of the and the stresses in…

A:

Q: A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in…

A: Given data:- A two-story building P1=400 KN P2=720 KN L=3.75 m To find:- Internal axial force axial…

Q: x = A cylindrical rod is made of three segments and is subjected to axial loads as indicated in the…

A: Basic concept used for tension and compression,If a force is acting away from the section, it will…

Q: The figure shown below

A: The cross-sectional area of the bars is Consider the diagram shown below for the beam ACE, Taking…

Q: The structure of a beam with single supports is supported by a pinned moment MA at end A, an…

A: To find: The support reactions and the internal forces at the midpoint of BC. Load diagram: The load…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.