If the maximum stressboth in tension and compression is not toexceed 120 Mpa, determine the maximumload that the hook can carry?Note:A-Dimensions of figure are in mm and hooksinner raduis OB = 105 mm.RI45-180section AB135

Step 1: Step 2: Step 3: Step 4:

Answered: If the maximum stress both in tension…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

Given:a. the force in BD=25KNb. vertical reaction at point C=-10KNc. horizontal reaction at point C=15KNd. resultant of reaction at point C=18.0KNe. allowable tensile (normal) stress in member BD =83.33MPaf. the allowable shear stress in the pin at C =72.7MPaPlease help me solve for:1. What is the required cross-section area and minimum thickness t of member BD?2. What is the required SHEAR cross-section area at point C?3. What is the minimum diameter for the pin at C?(Solve for a value with the combination of mm and N)
Similar problem already solved on bartleby. Take reference from there.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
While drilling a hole with a brace and bit, you exert a downward force P = 25 lb on the handle of the brace (see figure). The diameter of the crank arm is d = 7/16 in. and it s lateral offset is b = 4-7/8 in. Determine the maximum tensile and compressive stresses e1, and e2respectively, in the crank.
, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
Solve the preceding problem if the mass of the tailgate is MT— 11 kg and that of the crate is hic— 6S kg. Use dimensions H = 305 mm, L = 406 mm, dc= 460 mm, and dT= 350 mm. The cable cross-sectional area is At= 11.0 mm'. (a) Find the tensile Force T and normal stress T in each cable. (b) IF each cable elongates
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A simple pin-connected truss is loaded and supported as shown. All members of the truss are aluminum pipes that have an outside diameter of 70 mm and a wall thickness of 3 mm. Determine the normal stress in each truss member. Assume P-12 kN, Q - 17 kN, a- 1.4 m, b -3.6 m, and c-1.3 m. Use positive for tensile stress and negative for compressive stress. Answers: OAB- JAC- OBC- i B (3) b MPa. MPa. MPa.
2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
Prob 6-43 12 kN 6kN G 9 kN 4kN H B 1 m 2 m 1 m 1.5 m 1.5 m C D 1.5 m -15 m 6kN In this problem, you are asked to determine the forces in members CD, CJ, GJ, and CG. Now solve the problem using the method of sections.

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

If the maximum stress both in tension and compression is not to exceed 120 Mpa, determine the maximum load that the hook can carry? Note: A- Dimensions of figure are in mm and hooks inner raduis OB = 105 mm. RI 45- 180 section AB 135