An axial load P is supported by the short steel column shown in the figure. The column has a cross-sectional area of 16,200 mm2. If the average normal stress in the steel column must not exceed 70 MPa, determine the minimum required dimension a so that the bearing stress between the base plate and the concrete slab does not exceed 8 MPa. Assume b = 445 mm. An axial load Pis supported by the short steel column shown in the figure. The column has a cross-sectional area of 16,200 mm?. If theaverage normal stress in the steel column must not exceed 70 MPa, determine the minimum required dimension a so that the bearingstress between the base plate and the concrete slab does not exceed 8 MPa. Assumeb = 445 mm.Answer: amin =mm

Cross sectional area of the column, Acolumn= 16200 mm2 Average normal stress in the steel column,…

An axial load Pis supported by the short steel column shown in the figure. The column has a cross-sectional area of 16,200 mm. If the average normal stress in the steel column must not exceed 70 MPa, determine the minimum required dimension a so that the bearing stress between the base plate and the concrete slab does not exceed 8 MPa. Assume b = 445 mm. Answer: amin i mm

An axial load Pis supported by the short steel column shown in the figure. The column has a cross-sectional area of 16,200 mm. If the average normal stress in the steel column must not exceed 70 MPa, determine the minimum required dimension a so that the bearing stress between the base plate and the concrete slab does not exceed 8 MPa. Assume b = 445 mm. Answer: amin i mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.6P: Cable DB supports canopy beam OABC as shown in the figure. Find the required cross-sectional area of...

See similar textbooks

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
A short column constructed of a W 12 × 35 wide-flange shape is subjected to a resultant compressive load P = 25 k having its line of action at the midpoint of one flange (see figure). Determine the maximum tensile and compressive stresses d1and d2., respectively, in the column. Locate the neutral axis under this loading condition. Recompute maximum tensile and compressive stresses if a C 10 × 15.3 is attached to one flange, as shown.
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
AW310 × 74 wide-flange steel column with length L = 3.8 m is fixed at the base and free at the top (see figure). The load P acting on the column is intended to be centrally applied, but because of unavoidable discrepancies in construction, an eccentricity ratio of 0.25 is specified. Also, the following data are supplied: E = 200 GPa, y = 290 MPa, and P = 310 kN. What is the maximum compressive stress max in the column? What is the factor of safety n with respect to yielding of the steel?
A short column with a wide-flange shape is subjected to a compressive load that produces a resultant force P = 55 kN acting at the midpoint of one flange (see figure). Determine the maximum tensile and compressive stresses asand o^., respectively, in the column, Locate the neutral axis under this loading condition. Recompute maximum tensile and compressive stresses if a 120 mm X 10 mm cover plate is added to one flange as shown.
An aluminum pole for a street light weighs 4600 N and supports an arm that weighs 660 N (see figure). The center of gravity of the arm is 1.2 m from the axis of the pole, A wind force of 300 N also acts in the (y) direction at 9 m above the base. The outside diameter of the pole (at its base) is 225 mm, and its thickness is 18 mm. Determine the maximum tensile and compressive stresses o, and e1., respectively, in the pole (at its base) due to the weights and the wind force.
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
A simply supported wood beam is subjected to point load P at mid-span. The normal stress on element C is known to be sx= 12 MPa. Find the maximum shear stress on the element and show the state of stress on a sketch of a properly oriented element.
Continuous cable ADS runs over a small Frictionless pulley at D to support beam OABC that is part of an entrance canopy Tor a building (see figure}. Assume that the canopy segment has a weight it' = 1700 lb. (a) Find the required cross-sectional area of cable ADB if the allowable stress is 18 ksi. (b) Determine the required diameter of the pins at O. A, R and D if the allowable stress in shear is 12 ksi.
]11.6-2 A brass bar (E = 100 GPa) with a square cross section is subjected to axial forces having a resultant P acting at distance e from the center (sec figure). The bar is pin supported at the ends and is 0.6 m in length. The side dimension b of the bar is 30 mm and the eccentricity e of the load is 10 mm. If the allowable stress in the brass is 150 MPa, what is the allowable axial force Pallow.