Q4\ A filleted. plate of thickness t supports an axial load P (Figure below). Determine the diameter dh of the fillets so that the same stress occurs at the fillets. Given: p = 70 kN, D = 100 mm, df = 66 mm, r = 7.9 mm, t = 10 mm 07h

Q4\ A filleted. plate of thickness t supports an axial load P (Figure below). Determine the diameter dh of the fillets so that the same stress occurs at the fillets. Given: p = 70 kN, D = 100 mm, df = 66 mm, r = 7.9 mm, t = 10 mm 07h

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.18P: A flat brass bar has length L, constant thickness t, and a rectangular cross section whose width...

See similar textbooks

Similar questions

,3-23 A 200-lb trap door (AD) is supported by a strut (BC) which is pin connected to the door at B (see figure). (a) Find reactions at supports A and C. (b) Find internal stress resultants N, V, and M on the trap door at 20 in. from A.
Solve the preceding problem if the axial stress in the middle region is 24,000 psi, the length is 30 in., and the modulus of elasticity is 30 × 106 psi. In part (c), assume that dmax = 0.02 in
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
Solve the preceding problem if the mass of the tailgate is MT— 11 kg and that of the crate is hic— 6S kg. Use dimensions H = 305 mm, L = 406 mm, dc= 460 mm, and dT= 350 mm. The cable cross-sectional area is At= 11.0 mm'. (a) Find the tensile Force T and normal stress T in each cable. (b) IF each cable elongates
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
Repeat the preceding problem but now find the stress state on Element A at the base. Let W%= 240 N, WL= 250 N, / = 5 mm, d = 360 mm. See the figure for the locations of clement A and all loads
A tension member constructed of an L inch angle section (see Table F-4(a) in Appendix F) is subjected to a tensile load P = 12.5 kips that acts through the point where the mid-lines of the legs intersect (see figure part a). Determine the maximum tensile stresser, in the angle section. Recompute the maximum tensile stress if two angles are used and P is applied as shown in the figure part b.
A steel bar with a diameter d = 12 mm is subjected to a tensile load P = 9.5 kN (see figure). (a) What is the maximum normal stresser smax in the bar? (b) What is the maximum shear stress tmax? (c) Draw a stress element oriented at 45° to the axis of the bar and show all stresses acting on the faces of this element. (d) Repeat part (c) for a stress element oriented at 22.5° to the axis of the bar.
A plane Frame with pin supports at A and E has a cable attached at C, which runs over a friction-less pulley at F(see figure). The cable Force is known to be 500 lb. (a) Find reactions at supports A and E. (b) Find internal stress resultants N, V, and M at point H.
An clement in plane stress is subjected to stresses a, and (see figure). Using Mohr’s circle, determine the stresses acting on an element oriented at an angle 0 from the x axis. Show these stresses on a sketch of an clement oriented at the angle 0. Now. The angle 0 is positive when count erclockwisc and negative when clockwise.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A plane frame with a pin support at A and roller supports at C and £ has a cable attached at E. which runs over Frictionless pulleys al D and B (see figure). The cable force is known to be 400 N. There is a pin connection just Lo the left of joint C. (a) Find reactions at supports^, C, and E. (b) Find internal stress, resultants N, V, and M just to the right of joint C. (c) Find resultant force in the pin near C.