Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. The diameter of aluminum rod (1) is 1.50 in., the diameter of brass rod (2) is 1.25 in., and the diameter of steel rod (3) is 2.25 in. Determine the axial normal stress in each of the three rods. Assume P = 6 kips, Q = 3 kips, R = 10 kips and S = 25 kips. The normal stress is positive if tensile and negative if compressive. B |R (2) |S C 3) D Answers: 01 = i ksi 02 = ksi O3 = i ksi

Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. The diameter of aluminum rod (1) is 1.50 in., the diameter of brass rod (2) is 1.25 in., and the diameter of steel rod (3) is 2.25 in. Determine the axial normal stress in each of the three rods. Assume P = 6 kips, Q = 3 kips, R = 10 kips and S = 25 kips. The normal stress is positive if tensile and negative if compressive. B |R (2) |S C 3) D Answers: 01 = i ksi 02 = ksi O3 = i ksi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 550 mm, b = 275 mm, h = 450 mm, and 8= 50°. If the normal stress in tie rod (1) cannot exceed 180 MPa and the shear stress in pin B cannot exceed 120 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) h a B P
The bracket shown in the figure below is fixed supported and has an applied force of 5kip with 40 degre angle at the center of the top surface and has a rectangle cross-section and P is located 0.5 in below the neutral axis of the cross-section. calculate the state of stress at point P step by step, please.Thanks for your time and help
Problem #3 Three rods, each of area 200 mm², jointly support a 7.5 kN load, as shown in the figure. Assuming that there was no slack or stress in the rods before the load was applied, find the stress in each rod. Use Est = 200 GPa and Ebr = 83 GPa. Sted 7.5 KN 2.75 m
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 560 mm, b = 280 mm, h = 450 mm, and 0= 70%. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 140 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a Answer: Pmax= i B KN
Calculate the average stress in section a-a of the junction shown in the figure when applying force P=30 kN. (The question was given to me like this. Is it possible to answer it assuming the diameter as "d"?)
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure below. Axial loads are applied at the positions indicated. If P = 4,500 lbs and the cross sectional area of the rod is 0.85 in?, determine the stress in each section. Steel Bronze 4P Aluminum P 2 ft 3 ft 2.5 ft
A horizontal load P is applied to an assembly consisting of two inclined bars, as shown in the figure. The cross-sectional area of bar (1) is 1.30 in.2, and the cross-sectional area of bar (2) is 1.75 in.2. The normal stress in either bar may not exceed 24 ksi. Determine the maximum load P that may be applied to this assembly. Assume dimensions of a=14.5 ft, b=9.0 ft, and c=14.5 ft. Determine the allowable force F1 in member (1) and the allowable force F2 in member (2).
Determined the maximum normal stress experience by the entire axial member and determine the section, which maximum stress occurs(ie AB or BC or CD)
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 4 kips, R = 18 kips and S = 21 kips. Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.Answer: F1 = ? kips.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=33P=33 kipskips is applied to the assembly at A, two loads of Q=30Q=30 kipskips are applied at B, and two loads of R=35R=35 kipskips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 1717 ksiksi. The normal stress magnitude in steel rod (2) must be limited to 3030 ksiksi. The normal stress magnitude in brass rod (3) must be limited to 2121 ksiksi. Determine the minimum diameter required for each of the three rods.
Brass Problem 3: A composite bar is made by attaching a copper rod of length 900 mm and diameter 30 mm and a brass rod of length 600 mm and diameter 45 mm as shown. A load of 20 kN is applied at 20°C. For unyielding supports, find the stresses in the materials when the temperature rises to 50°C. For copper, E = 120 GPa and a = 18 x 10-6 °C. For brass, E = 90 GPa and a = 20 x 106 °C. Copper 20 kN 900 mm 600 mm
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 14 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 4 kips, R = 16 kips and S = 28 kips. A (1) VQ В R| (2) S S C (3) D First: Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.