Rigid member AB is supported by hinge support at A and a 12-mm-diameter wire BC at B as shown. The diameter of the pin at A is 10 mm, thickness of member AB is 20 mm, and the thickness of each bracket of support A is 15 mm. Use a factor of safety FS= 2 and following failure stresses to determine the maximum load w (kN/m) the member can support. For wire BC: G=350 MPa Pin at A: T200 MPa Support brackets: (Gaarna ka=150 MPa d-12 -35m -3m

Rigid member AB is supported by hinge support at A and a 12-mm-diameter wire BC at B as shown. The diameter of the pin at A is 10 mm, thickness of member AB is 20 mm, and the thickness of each bracket of support A is 15 mm. Use a factor of safety FS= 2 and following failure stresses to determine the maximum load w (kN/m) the member can support. For wire BC: G=350 MPa Pin at A: T200 MPa Support brackets: (Gaarna ka=150 MPa d-12 -35m -3m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

' Three piates are joined with a 12-mm diameter pin as shown beiow. Determine the maximum load p that can be transmitted by the joint if the maximum bearing stress between a plate and the pin must be limited to 650 MPa .
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 13 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 22 ksi, determine the minimum diameter d₁ required for rod (1). A (2) d₁ F₂ B C O 1.087 in. O 0.823 in. O 0.541 in. O 0.867 in. O 1.003 in. d₂
please answer quickly
For a given Data of the riveted joint shown in the figure: Given: Diameter of each rivet = 3/4 inch Maximum allowable shear stress of rivet = 96.53 MPa 3. Maximum allowable bearing stress of plate = 124.11 MPa %3D Yield Strength of the key = 45 MPa Ultimate Strength of the key = 128.5 MPa %3D Determine the maximum safe value of P that can be applied to both ends in Kips or Kilo pound. The figure below: 4 in P 7/8 in 7/8 in
Members BC and DE are 50 mm wide and 16 mm thick and made of steel (E = 200 GPa). Member AF is rigid. For a load of P = 60 kN, determine 500 mm (a) the normal stress in member BC, В C (b) the normal stress in member DE, 250 mm E (c) the displacement of point A. D Assume BC and DE do not yield or buckle. 250 mm F 500 mm- 650 mm
7 ft 5 ft The assembly shown above includes column AB, which has the following properties: Pinned (top and bottom) for buckling about x-axis Free at top and fixed at bottom for buckling about y-axis Circular cross-section with 8-inch diameter E = 10000 ksi Which of the following is closest to the critical buckling force of column AB? O Per = 269 kip O Per = 1080 kip O Per = 538 kip O Per = 135 kip
The pin-ended wrought-iron pipe shown in the figure below has outer diameter D, inside diameter d, and length L; it supports an eccentric load P based on a safety factor of n. Find the largest allowable eccentricity e. Given: D = 190 mm, d = 170 mm, L = 3.5 m, P = 430 kN, n = 1.4, E = 190 GPa, 0yp = 210 MPa.
Introduction to Fem
5. Determine the allowable axial load PA for a W250 x 67 steel wide-flange column with pinned ends (see figure below) using a Factor of Safety n=1.5 for the following lengths: L-3 m, 5m, 8 m and 10 m. Assume E-200,000 MPa, and G-300 MPa. 7 L A Pl A ISTE Section A-A
A frame ABC consists of a horizontal beam BC which is supported by a round solid rod AB inclined at a 50° angle, as shown below. The ends of the rod AB are flattened to make pin connections at A and B. A vertical load of 5,000 N is acting at the mid-length of the beam. The rod material is a steel with modulus equal to 207 GPa and yield strength of 220 MPa. (a) Using a factor of safety of2.5, determine the diameter of the rod AB. (b) If a clevis joint is used at the pin connection at B, design the pin diameter so that it does not fail in shear. The tensile yield strength of the pin material is 300 MPa. Use a factor of safety between 1.5 and 2.5. 5,000 N В C 5 m 3 m 50° A
Aluminum tube AB is fixed on support A, and the load P=60 KN is applied on Steel rod BC that is welded to tube AB via plate B. The cross-section area of the tube is equal to 1100 mm2 and the diameter of the rod is equal to 15 mm. calculate the axial deformation of point C? (Esteel=200GPa and EAl=70GPa)
Problem 2 The mechanical system consists of two identical steel rods (A = 30 mm², E = 200GPA, a = 15x106/°C) and a "rigid" beam AC. The beam is supported by a smooth pin at B. The nuts at A and C are initially tightened just enough to remove the slack, leaving the two rods stress-free. 1- Determine the axial stresses induced in rods (1) and (2) if the temperature of both rods is decreased by 60°C. 2- Determine the (small) angle 0 through which the beam AC would rotate due to this temperature change. -200 mm- - 80 mm- A 0f B "Rigid" |(1) (2) 250 mm