Problem 2.2-14 The frame construction of a factory workshop is built from two angled girders that are hinge supported in A and B and connected by the hinge H. The dead-load of the roof and an additional snow load are represented by the distributed load q = 8 kN/m. Moreover, a horizontal wind-load is simplified by a single concentrated force F = 10 kN, acting at the upper left corner of the frame. F 4 m A 5 m H 5 m B

Problem 2.2-14 The frame construction of a factory workshop is built from two angled girders that are hinge supported in A and B and connected by the hinge H. The dead-load of the roof and an additional snow load are represented by the distributed load q = 8 kN/m. Moreover, a horizontal wind-load is simplified by a single concentrated force F = 10 kN, acting at the upper left corner of the frame. F 4 m A 5 m H 5 m B

Name: Problem 2.2-14The frame construction of a factoryworkshop is built fr
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Problem 2.2-14The frame construction of a factoryworkshop is built from two angled girdersthat are hinge supported in A and B andconnected by the hinge H. The dead-loadof the roof and an additional snow loadare represented by the distributed loadq =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A plane portal frame ABCE has a cantilever extension CD on the right-hand side, shown in Figure 1. The frame is fully hinged at A and pinned on rollers at E. It is subjected to a uniformly distributed vertical loading of intensity 30 kN/m over the horizontal portion BCD and a horizontal point load of magnitude 40 kN at the midpoint of member CE. 1.1Calculate the support reactions 1.2 Draw the shear force and bending moment diagrams for the frame, clearly showing your calculations (member free-body diagrams)
Question 2A rigid beam ABC is supported by pin at A and reinforced by a bar BD in order to sustain the uniform distributed load of 5 kN/m along the beam ABC in the direction shown in the Figure Q2.(a) Draw the free body diagram and determine the reaction forces at joint A(b) Determine the resultant force at joint A and its direction(c) Determine the internal loadings at section a--a
I am struggling with this question
Statics and rigid bodies. Complete solution
I need to solve this question as soon as possible
The pins at B and D in the figure apply an axial load to diagonal bracing member BD. If BD has a rectangular cross-section measuring 0.50 in. X 2.00 in., what is the axial stress in member BD when the load is w0=220 lb/ft?
a) Determine the tensile force T’ in the rope on the side connected to joint B: b) Determine the internal compressive normal force ƒBC in the tube BC: c) Determine the horizontal reaction force Rx and the vertical reaction force Ry in joint A: d) Determine the moment M of the center of bar AB: e) Determine the compressive stress σBC in the tube BC: f) Determine the critical load Pc for the tube BC: g) Which of the following statements about the tube BC is correct: A. The tube BC fails due to yielding B. The tube BC fails due to buckling C. The tube BC fails due to both yielding and buckling D. The tube BC is safe against both yielding and buckling h) Pin C has a diameter of 30 mm; calculate the shear stress τ of the pin C, when considering one cross-section for shear stress calculation:
SITUATION 2: A two-member frame in the figure is loaded as shown in Fig. MEC-121. Calculate the equivalent force (kN) of the distributed load. (Answer: 6) Calculate the y-component of the reaction at B (in kN). (Answer: 3) Calculate the magnitude of the reaction at A (kN). (Answer: 13.63) and the magnitude of the reaction at C (kN). (Answer:14.97)
Neat solution
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 70 lb/ft^2 against the full area of the sign. The dimensions of the poles and sign are h1 = 16 ft, h2 = 7 ft, and b = 13 ft. To prevent buckling of the walls of the poles, the thickness t is specified as one tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7100 psi in the aluminum. Round your answer to two decimal places. d = ___ in. (b) Determine the minimum required diameter based upon an allowable shear stress of 2100 psi. Round your answer to two decimal places. d = ___ in.
PROBLEM 2. The carrier system in the figure consists of the AB rigid beam and two aluminum bars and a steel bar connected to it. After the assembly is created at 20 °C without causing any prestresses, calculate the stresses on the bars if the temperature is increased to 80 C. Steel A-36 A =160 mm? 3,5m 10 kN/m 3 m 3m 2 m 2014-T6 Aluminum A =200 mm E A,
The horizontal beam ABC shown in thefigure is supported by columns BD and CE. Thebeam is prevented from moving horizontally bythe pin support at end A. Each column is pinned atits upper end to the beam, but at the lower ends, supportD is a sliding support and support E is pinned.Both columns are solid steel bars (E = 30 x 106 psi)of square cross section with width equal to 0.625 in.A load Q acts at distance a from column BD.(a) If the distance a = 12 in., what is the criticalvalue Qcr of the load?(b) If the distance a can be varied between 0 and40 in., what is the maximum possible value ofQcr? What is the corresponding value of thedistance a?