13aThe scheme of supporting of theabsolutely rigid body is shown in thepicture. The minimal cross-section areaof the vertical bar Imust be definedfrom strength condition, if :a = 1.6 m, M = 8 kNm and the admissible(allowable) stress is equal to 100 MPa

Given data: The value of a is a = 1.6 m. The magnitude of the moment is M = 8 kN-m. The admissible…

3 a M The scheme of supporting of the absolutely rigid body is shown in the picture. The minimal cross-section area of the vertical bar 1must be defined from strength condition, if : a = 1.6 m, M = 8 kNm and the admissible (allowable) stress is equal to 100 MPa

3 a M The scheme of supporting of the absolutely rigid body is shown in the picture. The minimal cross-section area of the vertical bar 1must be defined from strength condition, if : a = 1.6 m, M = 8 kNm and the admissible (allowable) stress is equal to 100 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1 Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you. Please help
2. A replacement disc consists of the tube Cwith larger diameter of 4 cm, the cylindrical core B with the diameter of 2 cm and two relatively rigid discs on both ends. The disc replacement placed between vertebrae is under compressive force of 400N. The corresponding moduli of elasticity are Ec=10MPA and EB=20MPa. Determine the stress in the tube A and the core B. F Rigid parts 1cm C 2om 4cm F (Answer: OB = 509.3KPA, oc = 254.6KPA) 254.6KРа) %3D
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A=500 mm STEEL L-4 m A-400 mm E=80 GPa E-200 GPa 3 m 5 m P.
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1060 mm². Assume a = 2.1 m, b = 6.5 m, and c = 4.1 m. If P = 55 kN and Q = 70 kN, determine the normal stress in each member. L Answers: OAB = OBC JAC i IM PH Q. a P b C MPa (C) MPa (T) MPa (T)
A spherical pressure vessel has an inside diameter of 4.9 m and a wall thickness of 17 mm. The 0.27] that has a yield strength vessel will be constructed from a special steel [E = 224 GPa; v = of 250 MPa. If the internal pressure in the vessel is 1410 kPa, determine (a) the normal stress in the vessel wall. Answer in MPa rounded-off to 1 decimal place.
Question 3 of 12 View Policies Current Attempt in Progress Answer: Pmax= eTextbook and Media A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 3.5 in.². Assume a = 4.00 ft and b = 4.80 ft. If the normal stress in each member must not exceed 60 ksi, determine the maximum load Pmax that may be supported by the structure. Save for Later b -/15 kips ||| Attempts: 0 of 3 used *** Submit Answer
Pravinbhai
A column is fabricated by adhesively bonding two aluminum faceplates to a foam plastic core as shown below. Note that there are only left and right aluminum plates (with no front and back plates). The foam plastic core has a square cross-section with elastic modulus Ef 1110 MPa. Determine the stress in the aluminum plates, the stress in the foam core, and the displacement of the column under the action of the applied force. = Note: Express tensile stresses as positive (+) and compressive stresses as negative (-). Given: • L1 L2 = = 100 mm = 1.7 m • . L3 = = 1.4 mm RIGID PLATE ALUMINUM FACE PLATE F FOAM L2 |← 41 +| |—–—– 63 L1 L3 F = 37 kN σα = σ f = |ɗ| = = number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) MPa ? MPa mm ?
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 189 MPa, determine the minimum diameter required for each rod. Assume P = 70 kN and Q = 118 kN. d2 di B Answers: d1 = i mm. d2 = i mm.
Solve this one
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. For the connection shown, the average shear stress in the 13-mm-diameter bolts must be limited to 270 MPa. Determine the maximum load P that may be applied to the connection. O 271 KN O 215 kN O 232 KN O 291 KN O 173 kN
The block of weight W in the figure below hangs from the pin at A. The bars AB and AC are pinned to the support at B and C. The areas are 800 mm2 for AB and 400 mm2 for AC. Neglecting the weight of the bars, determine the maximum safe value of W if the stress in AB is limited to 110 MPa and the in AC to 120 MPa.