Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of the link and its length are given in the table below for each student. The alloawble stress of link BD is 200 MPa. a) Determine the maximum possible value of the load P b) If P-90 kN, determine the change in temperature needed for link BD to have no change in length. Given areel-12*10/°C, Etee-200 GPa

Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of the link and its length are given in the table below for each student. The alloawble stress of link BD is 200 MPa. a) Determine the maximum possible value of the load P b) If P-90 kN, determine the change in temperature needed for link BD to have no change in length. Given areel-12*10/°C, Etee-200 GPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

NEED ANSWER ASAP THANK YOUU The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 20144 lb is applied at A? The d = 0.79-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 19616 lb is applied at A? The d = 0.65-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
A 30 mm square is drawn on the rim of a large steel pressure vessel. The biaxial stress situation in the square after the pressure is applied is as shown in the figure. Determine the change in length of the BC edge in (mm).
Three cables having an area of 0.05 in^2 each is carrying the load W as shown. With no stress, the original lengths of the cables are 74.99 ft, 75.00 ft, and 74.94 ft. E = 29 x 10° psi Calculate for the stress in the intermediate wire. Choices: a. 8,026.65 psi b. 9,999.66 psi c. 19,939.80 psi d. 10,102.52 psi 1500 lb
A steel column of hollow circular cross section shown in Figure is supported on a circular steel base plate and concrete pedestal The column has outside diameter 220 mm and a wall thickness of 15 mm. It supports an axial load of 680 kN.a. Determine the bearing stress induced by the column to the base plate in MPa.b. If the allowable bearing stress on the pedestal is 10MPa, determine the required diameter of the base plate in mm.
QUESTION 12 The compound steel bar shown in Figure is made of three uniform segments marked as 1, 2 and 3 of diameters 30mm, 20mm and 10mm respectively and is loaded as shown. The stress in segment 1 is: 30mm 20 mm 10 mm 25kN 80 kN 2) 40 kN + 2m 1m 1m 臺 O a. 35.4 MNm2 O b. 92 MNm O c. 318.3 MNm2 С. O d. 113.2 MNm 2 QUESTION 13
If the flat link shown below has an allowable tensile stress of 75 MPa, then a force P 1800 N will require the link to have a minimum thickness of: 30 mm 10 mm 3.20 mm 2.60 mm 2.40 mm 2.20 mm 3.60 mm 3.00 mm 2.80 mm O 3.40 mm
The state of stress at a point in a structural member is given by = 0x = Ax² + By², ay = Cy² + Dz², oz Ez² + Fx² Txy = Gy + Hz, Txz = Iz + Jx, Tyz = Kx + Ly where A, B,..., L are constants. Find expressions of the body forces to ensure the equi- librium. Units of the stresses are MPa.
Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of the link and its length are given in the table below for cach student. The alloawble stress of link BD is 200 MPa. a) Determine the maximum possible value of the load P b) If P-90 kN, determine the change in temperature needed for link BD to have no change in length. Given Me=12*10/"C, E,200 GPa B A 0.4m 0.2m
mm. NegiCOL UIC wOg VA vUampvuva 1.4-12 A rigid member DAC as shown in Fig. P1.4-12 carries the load P. Bar AB is an aluminum bar whose cross-sectional area is 0.5 in, and it is pinned at A and B by 0.5-in-diameter pins in a single-shear configuration. If the maximum allowable normal stress in AB is 7000 psi and the maximum allowable shear stress in the pins is 15,000 psi, find the maximum allowable load P. For aluminum E 10 x 10° psi. %3D 8 ft 7 ft P B Fig P1.4-12