A link is loaded as shown, it is attached with two bolts with a diameter of 0.25 in. The link width is 2 lhand its thickness is 0.1 in, if the average normal stress in the link is 20 ksi (away from the bolts)determine the applied force G, the shear stress of a bolt as well as the bearing stress in one of the boltholes.2 inG

The diameter of bolt is The width of link is The thickness of link is The normal stress on link is

Answered: A link is loaded as shown, it is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Problem 1: Segment AB of the bar is a hollow tube with an outer diameter of 1.5 inches and a wall thickness of 0.125 inch. Segment BC is a solid rod of diameter 0.75 inch. Determine the normal stress in segment AB in psi. 0.125 in. 0.75 in. 4800 lb 2800 lb 1.5 in. B C |A -6 in.- -6 in. Your answer 2. In Problem 1, determine the normal stress in segment BC in psi. Your answer
Link AB, of width b = 2 in. and thickness t = 1414 in., is used to support the end of a horizontal beam. The average normal stress in the link is -18 ksi and the average shearing stress in each of the two pins is 12 ksi. Determine the average bearing stress (ksi). **The way I had solved it was that I used the given normal stress to first find the P force needed to plus into my bearing stress formula. I still however need the diameter. The answer key says to use the given shear stress equation to find the diamter, how do you know to use that and not the shear stress formula again?
Three interconnected cylindrical members are subjected to axial loads as shown below. If the allowable axial stresses are 140 MPa in the steel, 75 MPa in the brass, and 90 MPa in the aluminum, determine the required diameters of each the cylindrical bars. B Brass Aluminum D A Steel 270 kN 245 kN 200 kN -225 kN 0.5 m 0.5 m 0.5 m
A single rivet is used to join two plates as shown. If the diameter of the rivet is 20 mm and load P is 30 kN. The average shear stress developed in the rivet is: P
The four bars shown have the same cross-sectional area. For the given loadings, show that (a) the maximum compressive stresses are in the ratio 4:5:7:9, (b) the maximum tensile stresses are in the ratio 2:3:5:3. (Note: the cross section of the triangular bar is an equilateral triangle.)
The homogenous bar that weighs 5000 Ib is supported by a pin at Cand a cable that runs from A to B around the frictionless pulley at D. If the diameter of the cable is 0.8 inch, calculate its axial stress. Express your answer in ksi (kips per sq. inches) with one decimal place only (Note: Give only the numerical value of the answer. DO NOT INCLUDE THE UNIT IN THE ANSWER) * D F 3 ft 5 ft 5 ft
The two rods (A-B and B-C) shown in the left panel are connected by pins at A, B, and C. The cross sections of A-B and B-C are 10mm×13mm and 10mm×10mm, respectively. The bilinear stress-strain relation shown in the right panel is for the material used to make the two rods, where Ei is the slope of the stress-strain curve for stresses between 0 and 80 MPa and E2 is the slope for stresses larger than 80 MPa. Note that Hooke's law is only valid for stresses up to 80 MPa. A 1 1 B 0.900 m 3 P = 30 kN 2.44 m C σ MPa 80 E₂ = 40 GPa E₁ = 80 GPa E a) Given the conditions above, find the axial elongation for each rod when subjected to P=30KN. b) Find the final position of Point B due to the applied load P at that location. Hint: Assume point B moves by unknown amounts Ax and Ay from its initial position, and then use right triangles to write the known final lengths of the cables in terms of Ax and Ay. The equations can be simplified by assuming terms Ax² and Ay² are so small they can be…
i need the answer quickly
600 lb 600 lb An aluminum rod to be used in an aircraft control system is required to stretch 0.12 in. when a 600-1b tensile load is applied to it. If E = 10.2 × 10³ ksi and the allowable stress is 17 ksi, determine the smallest diameter that can be selected for the rod and the corresponding required length of the rod.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 13 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 22 ksi, determine the minimum diameter d₁ required for rod (1). A (2) d₁ F₂ B C O 1.087 in. O 0.823 in. O 0.541 in. O 0.867 in. O 1.003 in. d₂
Two ropes are used to hoist a 530 lb engine/transmission assembly as shown. The rope is anchored at C around the center part of the pin shown, causing the pin to experience a state of double shear. There is a frictionless pulley at A. The normal stress in the rope must not be allowed to exceed 15 ksi, and the shearing stress in the pin must not exceed 21 ksi. When the hoist is in the position given by: a = 44 in b = 11 ft c = 19 ft find the following: (a \& b) The forces carried in ropes AB and BC (c l& d) The necessary diameters of ropes AB and BC (e) The necessary diameter of the pin at C 2013 Michael Swanbom (a) TAB = (b) TBC = (c) dAB = (d) dBc = (e) d =
The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited to 295 MPa, determine the minimum bolt diameter that may be used in the connection.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A link is loaded as shown, it is attached with two bolts with a diameter of and its thickness is 0.1 in, if the average normal stress in the link is 20 ksi (away from the bolts) determine the applied force G, the shear stress of a bolt as well as the bearing stress in one of the bolt holes. 2 in G