Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in diameter. If a tensional force of 120kN are applied at each end of the rods, Determine the allowable tensile stress in the circular rods and the Average shear stress occurs in the pin. Rod (1) Rod (2)

Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in diameter. If a tensional force of 120kN are applied at each end of the rods, Determine the allowable tensile stress in the circular rods and the Average shear stress occurs in the pin. Rod (1) Rod (2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: The rod has a diameter of 40 mm. It is subjected to the force system F₂ = 1900 N, Fy=700 N, F₂ = 900…

A: The rod diameter d =40 mm = 0.04mThe force systemFx= 1900NFy= 700NFz= 900NFindThe Normal stress act…

Q: 1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A: The normal stress (either tensile or compressive) developed in a member when it is subjected to an…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: Answer: The maximum load that can be supported by the structure: P = 29.046 kN

Q: The rigid bar is supported by an 8-cm-long, 8-mm-diameter aluminum wire A and a 10-cm-long, 2-mm-…

Q: Two wrenches are used to tighten the pipe. The pipe is made from a material having an allowable…

A: The maximum allowable shear stress is The outer diameter of pipe is The inner diameter is

Q: Stepped bar ABC is fabricated out of aluminum and supported by a fixed support at C as shown. The…

Q: Two circular rods of 50mm diameter are connected by a knuckle joint, by a pin of 40 mm in diameter.…

A: Given:Diameter of circular rod, D=50 mmDiameter of pin, d=40 mmPull load, P=120 kN=120*103 NFind:1…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

Q: What is the stress in a rectangular rod that is 20 mm by 30 mm in cross-section if is supporting a…

A: Given data:- load =1000 Ncross-section area =20 mm 30 mmTo find:-the stress in a rectangular rod (…

Q: Q2b) The supporting wheel on a scaffold is held in place on a leg using a 6 mm diameter pin as…

Q: e state of stress at a point in a circular bar under pure torsion is given by T xy = T yx= t and…

Q: The solid steel rod (1) has an allowable shear stress of 17 ksi. The brass tube (2) has an allowable…

A: given; allowable shear stress for rod (τ)=17ksi…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C.…

A: Given data: F1=120 kNF2=90 kN Need to determine the absolute value of the deformation at point C.

Q: Calculate the combined stress (MPa) on the rod shown below using the principle stress method. Here,…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: Answer: The maximum load that can be supported by the structure without exceeding either allowable…

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

Q: ny mm is the smallest allowable outer diameter of the washer

A: GIVEN :- Diameter of rod : d= 34mm washer inner diameter : di = 37.5 Allowable stress of rod : σ=…

Q: A supporting structure consists of a round steel bar with a welded square bar. The round bar is…

A: GIVEN: TO FIND:1. sketch the course of the required internal forces 2. necessary size b of the…

Q: Q31 A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside…

Q: The stepped down circular bar with diameters 2d and d is subjected to a tensile axial force aligned…

A: Given:-Diameters=2d and dTo find:-Ratio of direct stress in segment AB to direct stress in segments…

Q: The figure below shows two plates connected by two rivets. The plates are made from aluminum 6061-T6…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: According to the given dataBarNormal-StressDiameterThickness1175MPa10mmNA216548mm6Considering the…

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

Q: The normal stress in a piece of structural member is 300 MPa. If the modulus of rigidity G is 85…

A: Problem is based on strength of materials and can be solved as:

Q: Two 2 by 4 cm 1062 steel bars are butt-spliced with two 3 by 4 cm 1016 splice plates using six M14…

A: We have to find the correct formula for finding shear stress

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: The largest torque that can be applied safely at the upper end of the steel rod: Tmax = 319.07 lb•in

Q: A motorcycle's clutch hand lever is designed to receive a load from the rider's finger of 50 N at…

A: &#x3C3;=F&#x200B;A" data-mce-style="display: inline-block; line-height: 0; text-indent: 0px;…

Q: Şekilde gösterildiği gibi sıcaklık 24°C ikem 0,5 mm'lik boşluk bırakılmıştır. Alüminyum çubuktaki…

Q: The forces P, and P, are applied to the post in the directions parallel to the x and y axes,…

A: Given: The length of post, L = 1000 mm = 1 m The diameter of post, D = 100 mm = 0.1 m The force…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure.…

A: Answer: (1) Considering steel : P = 12600 N. (2) Considering aluminum : P = 30400 N. (3) Considering…

Q: The bell crank in (Figure 1) is pinned at A and supported by a short link BC. It is subjected to the…

Q: |F 2F a 3F| b a

Q: A 1-m long copper bar is placed between two rigid, unyielding walls, as shown, with only one end…

A: The stress developed in the bar.Given:The length of the bar is .The temperature rise is .Obtain…

Q: Rod of diameter 20 mm is loaded with 5kN tension force. What is the magnitude of stress in the rod?

A: Given, Diameter of rod = d = 20 mm Force applied to rod = F = 5 kN = 5000 N Cross-sectional area…

Q: The rectangular bar is connected to the support bracket with a 17-mm diameter pin. The bar width is…

A: Diameter of the pin: 17 mmWidth of the rectangular bar: w = 85 mmThickness of the rectangular bar:…

Q: The coupling as shown in figure is made from steel has rectangular cross section is designed to…

Q: An engineering machine component operating in a high temperature environment consists of a copper…

Q: Q1// The light rigid bar ABCD shown in Fig.1. is pinned at B and connected to two vertical rods.…

A: Here is the solution for the above question.

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: Diameter of Tie rod (1) d1=11 mm Allowable normal stress =165 MPa. Outside diameter of Pipe (2)…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

2. Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm
in diameter. If a tensional force of 120kN are applied at each end of the rods, Determine the
allowable tensile stress in the circular rods and the Average shear stress occurs in the pin.
Rod (1)
Rod (2)
Pin

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Answer the image below. Also draw the FREE BODY DIAGRAM. Answer should be: PSTEEL = 15,000 lbs PBRONZE = 9,000 lbs PALUM = 3,000 lbs δTOTAL = 0.0224 inch < 0.08 inch
Determine the load that can be applied at the end of the rigid bar if the stressin either spring shown in the figure shall not exceed 200MPa. Present detailed drawings/FBD’s illustrating your solution.
please answer with complete solution, thank you
Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 5.998 mm. determine the applied force F. Select one: O F=15708 N O F= 5236 N O F= 6283 N O F=4189 N O F= 10472 N O F= 13090N Clear my choice Finish attempt. IOUS ACTIVITY 360 Test - Spring 2020-2021 Jump to. 11:21 PM 4) G ENG 4/15/2021 LEGO ort sc delete end home backspace num lock 7V home enter 4E K pause M
Answer both parts please! Part A. if the bolt is subjected to a compressive force of P= 21.3 kN, deteemine the magnitude of the average normal stress in the steel. Part B. if the bolt is subjected to a compressive force of P= 21.3 kN, determine the magnitude of the average normal stress in the bronze.
Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 5.995 mm. determine the applied force F. Select one: O F=15708N O F= 10472 N O F=5236 N O F= 13090 N O F=6283 N O F=4189 N
only HANDWRITTEN answer needed ( NOT TYPED)
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 12 mm and an allowable normal stress of 80 MPa. Pipe (2) has an outside diameter of 50 mm, a wall thickness of 7 mm, and an allowable normal stress of 80 MPa. Assume x₁ = 3.7 m, x₂ = 1.2 m, and y₁ = 4.0 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. 9₁ (1) Answer: Pmax= B (2) 3° P C kN 2
1. Determine the shear, tensile and bearing stresses for the structural connection shown in Fig. 1. P- 10000 Ib + poo
A component made of 7075-T6 aluminum alloy has an edge crack of 1.4 mm in length. Plane strain fracture toughness of this alloy is given as 27 MPavm. Geometrical factor of the crack is given as 1.2.| (a) If this component is subjected to uniaxial tensile stress of 380 MPa, determine whether sudden brittle fracture will occur or not. (b) Calculate the maximum allowable crack size for this component in order not to be failed in brittle manner under a stress of 1000 MPa.
It is really confusing question ,Please attempt only if you are 100% Sure .
An aluminum [E-9600 ksi] control rod with a circular cross section must not stretch more than 0.34 in. when the tension in the rod is 2070 lb. If the maximum allowable normal stress in the rod is 12.9 ksi, determine: (a) the smallest diameter d that can be used for the rod. (b) the corresponding maximum length L of the rod. Answers: (a) d- i in. (b) L- in.